1108739 Kenmore Dryer - Instructions

All Instructions for the 1108739
91 - 105 of 943

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
no heat was being produced
9 of 14 people found this instruction helpful.
  • reinaldo from guttenberg, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website
Was this helpful?
Thank you for voting!
Loud screeching noise when dryer running
6 of 6 people found this instruction helpful.
  • Stephen from Charlotte, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First, removed the bottom cover below the dryer door. This is just held on with two clips that can be pushed in with a flat screw driver. Then remove the springs that go from the bottom of the dryer to the inside of the dryer door. We had to remove the entire front of the dryer, so the easiest way we found was to loosen the two screws on the bottom of the front panel, but not remove them. Then pop up the top of the dryer. To lift the top, first remove the two screws under the little door where the lint trap goes. The top is hinged in the back, and it snaps down onto two clips that can easily be popped up with a flat screw driver) With the top opened, there are two screws accessible. When the front of the dryer is removed, there will be nothing to support the drum, so what we found was that if you rotate the drum, you'll find a point where there's a hole in the top of the drum. If you take the springs that you removed from the bottom of the door you can hook them into this hole, and hook the other end into a hole in the back wall of the dryer just behind the drum. The springs are the perfect size for this, and it keeps the drum from falling when you remove the front panel. then just disconnect the three wires going to the switch inside the front panel, and remove the two screws from the top of the front panel. It should then lift right off. The bearing can just be pulled away and the new one installed. Put everything together again in reverse order.
Was this helpful?
Thank you for voting!
Dryer stopped spinning.
8 of 12 people found this instruction helpful.
  • sherif from BARTONSVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.
Was this helpful?
Thank you for voting!
Dryer making squealing noise.
8 of 12 people found this instruction helpful.
  • Harriet from Palm Coast, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Was this helpful?
Thank you for voting!
Dryer made a terrible squealing noise
7 of 9 people found this instruction helpful.
  • Will from Charlotte, NC
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Socket set
Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.

Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Was this helpful?
Thank you for voting!
broken rib belt
6 of 6 people found this instruction helpful.
  • Robert from PEABODY, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Wil l be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob
Was this helpful?
Thank you for voting!
Dryer wouldn't run
6 of 6 people found this instruction helpful.
  • Edward from Richlands, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one. Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!

Repair took about five minutes and saved approximately $70!
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people found this instruction helpful.
  • Ken from Bixby, OK
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Was this helpful?
Thank you for voting!
Dryer got hot then heat would shut off
6 of 7 people found this instruction helpful.
  • Douglas from Fernley, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and r everse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Was this helpful?
Thank you for voting!
Auto Dry Sensor Failed
9 of 16 people found this instruction helpful.
  • J from Trabuco Canyon, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.
Was this helpful?
Thank you for voting!
flame fadedout after unit got hot; problem turned out to be the solenoid coils
6 of 7 people found this instruction helpful.
  • David from Adkins, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
removed frt & rear panels & drum and lint chute for seal replacement replaced these components, problem didn't go away, ordered & replaced both gas valve coils (m series coil kit) problem solved
Was this helpful?
Thank you for voting!
not heat
7 of 10 people found this instruction helpful.
  • Sarah from Merrimac, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on t he tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.
Was this helpful?
Thank you for voting!
Start windings burnt out on original motor (dryer would not start)
7 of 10 people found this instruction helpful.
  • Frank from Smyrna, TN
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to un thread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
Was this helpful?
Thank you for voting!
Dryer would not activate unless jarred by striking with the hand.
6 of 8 people found this instruction helpful.
  • DAVID from AKRON, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Investigated inside control panel for loose wires or parts. Removed back of control panel and back of dryer and used a vacuum to remove lint from every possible contact. Problem not fixed.

Lifted top of dryer and cleaned inside. Struck door close switch with a screw driver and dryer started every time. Replaced switch. ... Read more />
Works every time. This is the 3rd repair in over 20 years. Each time the dryer works as though new.
Was this helpful?
Thank you for voting!
Motor was bad
5 of 5 people found this instruction helpful.
  • Michael from CLIFTON HTS, PA
  • Really Easy
  • 30 - 60 mins
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part s o I can redo a testimonial here for you. 19 days and still waiting
Was this helpful?
Thank you for voting!
All Instructions for the 1108739
91 - 105 of 943