1108656 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Badly worn idler pulley and rollers.
11 of 14 people
found this instruction helpful.
-
TODD from GRASS VALLEY, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer does not turn off. Will stay in the Cool Down cycle
11 of 14 people
found this instruction helpful.
-
David from WINCHESTER, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
My dryer timer would run through the heat cycle and move in to the cool down cycle. It would not move past the cool down cycle, and would not shut off automatically. I tried replacing the Thermal Fuse first, since I'd already removed the back panel to diagnose the problem. There was no change - the dryer did not shut off automatically. Ne
... Read more
xt, I removed the back cover to the timer console. The Timer Power Resistor looks like a black circle and a rectangle joined together. It was attached to the back of the on/off switch by a single hex head screw, and the resistor has orange and black wires attached. The replacement Power Resistor doesn't look like the resistor that was in my dryer. It is rectangular in shape with 2 male spade connectors. I attached the orange and the black wires to the new power resistor. I started the dryer and it went through a full heat/cool down cycle, and automatically shut off with the end of cycle buzzer sounding. Total part replacement time was about 10 minutes.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Heater Element bad.
10 of 11 people
found this instruction helpful.
-
Christian from JOHNSTON, IA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Followed video step by step. Perfect instructions. I’d only add that you should get and wear mechanics gloves. My hands got torn up by the sharp metal edges taking apart and putting it back together. Ouch!!
So happy with Partselect though. Super fast shipping and a perfect instructional video. Thanks!!
P.S. Wear gloves! ... Read more !!
So happy with Partselect though. Super fast shipping and a perfect instructional video. Thanks!!
P.S. Wear gloves! ... Read more !!
Read less
Was this helpful?
Thank you for voting!
replace lint filter
10 of 11 people
found this instruction helpful.
-
Ed from Greensboro, NC
- Really Easy
- Less than 15 mins
with both hands
Was this helpful?
Thank you for voting!
broken clip on top panel hold down
15 of 26 people
found this instruction helpful.
-
Mark from Huntington Station, NY
- Easy
- Less than 15 mins
-
Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
Rust marks on clothing
13 of 21 people
found this instruction helpful.
-
Patrick from Manor, TX
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Our dryer was leaving rust marks on our clothes that looked like a brown pencil mark. It turns out that the rear drum seal in our dryer was absorbing gunk over the years and we had to change it. It was a fairly easy fix but did require pulling the dryer almost completely apart. While we had it apart we changed this as well.
Any ... Read more one with a socket stet and screw driver can get it all apart.
On our machine, start by removing the 2 screws that hold the lint filter neck to the top of the machine (under the flap).
Then pry the top of the machine up in the front. It will pop up and you can fold it back.
Then you will need to remove 2 bolts and undo the plug.
From there you can pull the front off and get to the drum.Make sure you note how the belt tensioner comes out (under the drum) and how the belt is routed. It's quite basic.
After you get the drum off, peel the old seal(s) off and put the new seal(s) on as directed.
Pretty easy and our clean clothes stay clean now.
Any ... Read more one with a socket stet and screw driver can get it all apart.
On our machine, start by removing the 2 screws that hold the lint filter neck to the top of the machine (under the flap).
Then pry the top of the machine up in the front. It will pop up and you can fold it back.
Then you will need to remove 2 bolts and undo the plug.
From there you can pull the front off and get to the drum.Make sure you note how the belt tensioner comes out (under the drum) and how the belt is routed. It's quite basic.
After you get the drum off, peel the old seal(s) off and put the new seal(s) on as directed.
Pretty easy and our clean clothes stay clean now.
Read less
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people
found this instruction helpful.
-
Dawn from Chesapeake City, MD
- Really Easy
- Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people
found this instruction helpful.
-
stephen from langley, KY
- Really Easy
- Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
Replaced a broken pulley.
10 of 12 people
found this instruction helpful.
-
Brian from IMLAY CITY, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Was this helpful?
Thank you for voting!
Dryer not heating
11 of 15 people
found this instruction helpful.
-
Antonio from LEWISVILLE, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Test all censors with a voltmeter like the video showed on you tube. I found out that the heating element wasn’t working so while I was there I swapped other thermostats and components to give my 20 year old dryer, some more life. Thank you partselect.com ( I got a adjustable thermostat which didn’t have any instructions, how to set the r
... Read more
ight temperature according to your previous thermostat. “You have to google it “ )
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint remover was worn and completely fell apart
9 of 9 people
found this instruction helpful.
-
Debby from Wellesley Hills, MA
- Really Easy
- Less than 15 mins
I didn't think I could find a replacement part because the dryer was so old (it has fake wood paneling!) and I was already considering the cost of a new dryer. I searched online and found this site. I crossed my fingers and placed my order. When it came, I removed what was left of the old lint remover and put in the new one. It was a perf
... Read more
ect match. The colors were a bit off but who cares. PartSelect saved me from having to purchase a new dryer. Yay!
Read less
Was this helpful?
Thank you for voting!
Old motor was making noise and tripping after a few minutes
10 of 13 people
found this instruction helpful.
-
John from Midland, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.
Was this helpful?
Thank you for voting!
Dryer belt broke- drum would not turn
10 of 13 people
found this instruction helpful.
-
Ronald from Oakdale, CT
- Easy
- 30 - 60 mins
-
Screw drivers
This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner spru
... Read more
ng to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..
Read less
Was this helpful?
Thank you for voting!
Broken dryer belt
10 of 14 people
found this instruction helpful.
-
Steven from Bridgewater, MA
- Easy
- 15 - 30 mins
-
Screw drivers
Prop up the hood of the dryer with flat bar. Take out 2 screws holding dryer front end and 2 switch screws for dryer light inside dryer door. Secure dryer drum with bungee cord. Lift front end and remove. Remove broken belt. Route new belt over drum and pass underneatch idler pulley at botttom of dryer. Apply pressure to idler pul
... Read more
ley w/one hand while securing belt around motor with the other. Make sure drum seals are snug between front and back of dryer while putting everything back together.
Have confidence. This is a very easy fix.
Have confidence. This is a very easy fix.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Busted Dryer Belt
8 of 8 people
found this instruction helpful.
-
Oscar from Dallas, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
I order a new belt and I watched the video instructions on how to replace it, follow the instructions, removed the top and took out the dryer tumbler or can, found a broken idler pulley, order a new one, got it in about two days, replaced all the parts and now its working like a new dryer, I called several repair shops and I got estimates
... Read more
from $65 to $150, I spend less than $35 and it took me about 35 minutes to install and I got it fixed..
Read less
Was this helpful?
Thank you for voting!