1108656 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Change dryer belt
15 of 17 people
found this instruction helpful.
-
Scott from Bayport, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I p
... Read more
opped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Rear Drum seal wore out, and needed to be replaced.
14 of 14 people
found this instruction helpful.
-
David from San Jose, CA
- Easy
- 1- 2 hours
-
Screw drivers, Socket set, Wrench set
I thought this repair would be a lot harder than it was. First I removed the top of the dryer ( removed two screws from the backside) then I removed the frontside of the dryer( i think two or four screws) just look along the edges to see where it's attached. Then I also removed the lower panel of the front of the dryer The one with clips
... Read more
to secure on the dryer. Removed the ground wire from panel. I removed the screws that holds on the lint vent and took that off. I easily took the drum out of the dryer and then placed it on the floor with the backside facing up. I then removed the damaged old felt strip (which had been glued on) I sanded a little to remove some of the residue. I checked the instructions to make sure I placed the new belt on correctly, and then glued it to the drum.(Note; the belt I received was too big about 3". I just cut it and sewn it together. It fit perfectly after that.) If this is a problem for you I don't think it has to be sewn because the glue you use to secure it holds tight and dries fast.
I also inspected and touched up the front felt seal with the glue.
After it dries about 10-15 min, I put the drum back in the dryer and then reattached the dryer vent and the front panel. I took a look at the instructions to set the back felt belt correctly. I turned the drum, gently pull the edge of the felt seal to the surface. After that I set the dryer belt up. This was bit tricky, I had to reach from the bottom panel area and after a few trys I got it . ( When setting the dryer belt, It works better if you push the spring arm with your hand instead of trying to use the belt to pull it toward the motor) Then I turn the drum a couple of times to make sure it was on good. then I put the bottom panel on and then the top back on and I was good to go. It works great now.
I also inspected and touched up the front felt seal with the glue.
After it dries about 10-15 min, I put the drum back in the dryer and then reattached the dryer vent and the front panel. I took a look at the instructions to set the back felt belt correctly. I turned the drum, gently pull the edge of the felt seal to the surface. After that I set the dryer belt up. This was bit tricky, I had to reach from the bottom panel area and after a few trys I got it . ( When setting the dryer belt, It works better if you push the spring arm with your hand instead of trying to use the belt to pull it toward the motor) Then I turn the drum a couple of times to make sure it was on good. then I put the bottom panel on and then the top back on and I was good to go. It works great now.
Read less
Was this helpful?
Thank you for voting!
Loud banging noise when running dryer
15 of 18 people
found this instruction helpful.
-
Joseph from Prospect Park, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people
found this instruction helpful.
-
Kim K from Hurst, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do
... Read more
the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Read less
Was this helpful?
Thank you for voting!
Dead motor
17 of 24 people
found this instruction helpful.
-
Robert from Glencoe, IL
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
1. Shut off gas and disconnected dryer.
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap ... Read more .
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap ... Read more .
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...
Read less
Was this helpful?
Thank you for voting!
Noisy Dryer/Rear Seal Came off
14 of 15 people
found this instruction helpful.
-
Charles from Olney, MD
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
So the first thing I did was search the web for the parts and came to this site. I knew the model and that I needed rollers and a rear seal. I found both on this site for order in less than 10 minutes, which included finding the wonderful diagrams and directions for replacing the parts. I placed the order got the parts two days later.
... Read more />
I printed out the directions to take the drum out and followed them. After unplugging the dryer, I pushed in the clips that were indicated to release the top and pushed that up. I then disconnected the door switch. I reached under the dryer (not having a kicker panel for some years...) and worked to release the belt. I then took the front off removing the four screws as described. The drum removal was a little more awkward than I had anticipated, but came out without major hassle. Getting the drive belt off was the worst part other than the size.
I then removed the warn rollers after taking the clips off with a pair of needle nose pliers. I put the new rollers on and secured them.
I then went to the drum.After cleaning it a bit, I attempted to dry fit the seal onto the drum to get the idea of how it would fit. This didn't work easily as the seal needed to stretch a bit more than it could while staying on all around. I grabbed a couple of clamps and worked it on using those. Once that was sorted I started to apply the glue. It was more runny than I had anticipated. After working that around the seal I let it dry overnight to an excellent bond.
The next day I put the drum back in, adjusted the seal properly and put the machine back together. The tension roller is not fixed to the machine so getting that back on was a little bit of a trick but was overcome easily enough.
A few loads of laundry later and I knew it was all done and working OK. It hasn't dried this good or been this quiet in years.
This was my first major appliance repair. With the assistance of the diagrams on here and directions I would say to anyone contemplating a diy repair on something like this to give it a shot.
My only recommendation to the site is to more visibly recommend doing the seals, rollers and drive belt at the same time. While in there I could see wear on the drive belt and will probably need to replace that in the next six months or so.
... Read more />
I printed out the directions to take the drum out and followed them. After unplugging the dryer, I pushed in the clips that were indicated to release the top and pushed that up. I then disconnected the door switch. I reached under the dryer (not having a kicker panel for some years...) and worked to release the belt. I then took the front off removing the four screws as described. The drum removal was a little more awkward than I had anticipated, but came out without major hassle. Getting the drive belt off was the worst part other than the size.
I then removed the warn rollers after taking the clips off with a pair of needle nose pliers. I put the new rollers on and secured them.
I then went to the drum.After cleaning it a bit, I attempted to dry fit the seal onto the drum to get the idea of how it would fit. This didn't work easily as the seal needed to stretch a bit more than it could while staying on all around. I grabbed a couple of clamps and worked it on using those. Once that was sorted I started to apply the glue. It was more runny than I had anticipated. After working that around the seal I let it dry overnight to an excellent bond.
The next day I put the drum back in, adjusted the seal properly and put the machine back together. The tension roller is not fixed to the machine so getting that back on was a little bit of a trick but was overcome easily enough.
A few loads of laundry later and I knew it was all done and working OK. It hasn't dried this good or been this quiet in years.
This was my first major appliance repair. With the assistance of the diagrams on here and directions I would say to anyone contemplating a diy repair on something like this to give it a shot.
My only recommendation to the site is to more visibly recommend doing the seals, rollers and drive belt at the same time. While in there I could see wear on the drive belt and will probably need to replace that in the next six months or so.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud sreeching and vibration
14 of 15 people
found this instruction helpful.
-
Robert from TUTTLE, OK
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are
... Read more
pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
No heat
16 of 22 people
found this instruction helpful.
-
Mason from New Park, PA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the old thermostat. One of the wires was fried. The new thermostat came with a new clip/connector so I cut the bad part of the wire out, stripped it back and attached the new connector. Then, I screwed the new thermostat in place and attached both connectors. The dryer has heat again. PartSelect.com got the correct part out to m
... Read more
e in a short amount of time. Their repair help also helped me test and diagnose the problem in the first place.
Read less
Was this helpful?
Thank you for voting!
Thermal fuse was bad.
16 of 22 people
found this instruction helpful.
-
Brad from Odessa, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.
Thanks for the help.
Thanks for the help.
Was this helpful?
Thank you for voting!
Drum not turning; accompanied by loud "screeching" sound.
15 of 19 people
found this instruction helpful.
-
holly from LONG BCH TWP, NJ
- Easy
- 30 - 60 mins
-
Socket set, Wrench (Adjustable)
Followed instructional video provided for this type of repair after diagnosing problem via of 'troubleshooting' on PartsSelect site. Simple, safe, and relatively easy (minimal mechanical knowledge helpful).
Second time using PartSelect; washing machine repair ~ 6 mo. previous.
PartSelect was spot-on with that repair as well, sa ... Read more ving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Second time using PartSelect; washing machine repair ~ 6 mo. previous.
PartSelect was spot-on with that repair as well, sa ... Read more ving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
door cables broke
16 of 23 people
found this instruction helpful.
-
CAROL from HUNTINGDON, PA
- Easy
- Less than 15 mins
-
Screw drivers
Removed the screws holding the dryer door together and pushed the plastic pin out that the cable end went through. removed the screws at the dryer filter then popped up the top. put the cable through the door and then reached down with the door spring and went through the hole in the cable end, fastened the spring and pushed back down the
... Read more
top and replaced all screws. job complete. the hardest part was getting the spring through the small hole on the cable end but with a little patience and persistance it was accomplished.
Read less
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people
found this instruction helpful.
-
Richard from Duarte, CA
- Really Easy
- Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people
found this instruction helpful.
-
michael from indianapolis, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl
... Read more
aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.
Thanks Mike
It was a very simple repair.
Thanks Mike
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
squeaky and very loud noise
13 of 15 people
found this instruction helpful.
-
Jimmie from Lucerne Valley, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
first we printed out directions from a couple of online repair sites that had pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive repla ... Read more cing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive repla ... Read more cing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!