1108639 Kenmore Dryer - Instructions

All Instructions for the 1108639
121 - 135 of 957

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people found this instruction helpful.
  • Anthony from PITTSTON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Was this helpful?
Thank you for voting!
There dryer was not producing any heat
3 of 3 people found this instruction helpful.
  • Terry from Boise, ID
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I unplugged the dryer from the electrical outlet, removed the back of the unit and checked the heating element for continuity. There was no reading. I then removed the housing and heating element and visually inspected it. The coiled wire was broken in two places.
I then did a Google search with the model number and found Parts Selec t. I placed my order Sunday afternoon and the part arrived the following Wednesday. That evening it took about 20 minutes to install the new element,put the back on the dryer and re-attach the exhaust tube.
The old dryer is as good as new again.
TJ in Boise
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people found this instruction helpful.
  • Craig from VASS, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this helpful?
Thank you for voting!
My old dryer drum had become noisy and loose and prone to getting stuck while running.
4 of 6 people found this instruction helpful.
  • Ed from SEBEKA, MN
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I replaced the front seal and bearing, split ring bearing and rear seal. It was technically pretty easy. The thing to do is watch the videos provided by PartsSelect AND go to Youtube and watch a couple of others. Once you see several guys do the job and look over your own machine, it all becomes obvious. Some tips: Work cleanly, you will be dealing with dryer dust and shredded gasket material. Use a vacuum and put down newspaper or a drop cloth. While you have it apart, clean the inside of the machine, and check the other moving parts (eg, rear bearing and drive belt). The glue for the rear drum seal is runny and dries fast so work reasonably quickly. I held the seal on with clothes pins and binder clips and glued about a foot of seal at a time. Everything else goes on easily. They dryer is like a new machine-good for another 30 years.
Was this helpful?
Thank you for voting!
Lint Filter wore out.
4 of 6 people found this instruction helpful.
  • Claude from Austin, TX
  • Really Easy
  • Less than 15 mins
It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.
Was this helpful?
Thank you for voting!
Washer wouldn’t drain and spin
3 of 3 people found this instruction helpful.
  • Thomas from KENT, CT
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Was this helpful?
Thank you for voting!
drum stopped
3 of 3 people found this instruction helpful.
  • carl from westbrook, CT
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
10 min. job, easy to do / two screws top and two inside front / remove old parts install new.
Was this helpful?
Thank you for voting!
dryer would not turn on
3 of 3 people found this instruction helpful.
  • donald from MANVILLE, NJ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
Needed a new lint filter
3 of 3 people found this instruction helpful.
  • Evelyn from JACKSONVILLE, FL
  • Very Easy
  • Less than 15 mins
Took the old one out, replaced it with new one.
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people found this instruction helpful.
  • PHILLIP from AUSTIN, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this helpful?
Thank you for voting!
dryer motor quit working
3 of 3 people found this instruction helpful.
  • Tommy from BRUSH, CO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy
Was this helpful?
Thank you for voting!
Mother was frozen up
3 of 3 people found this instruction helpful.
  • Dan from SYRACUSE, UT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
broken blower wheel
3 of 3 people found this instruction helpful.
  • Vern from NEWBERG, OR
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people found this instruction helpful.
  • David from JOLIET, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
Dryer would not start, showed F40 code
3 of 3 people found this instruction helpful.
  • Glenn from KINGSPORT, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.
Was this helpful?
Thank you for voting!
All Instructions for the 1108639
121 - 135 of 957