1108608 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken handle
4 of 5 people
found this instruction helpful.
-
John from New Bedford, MA
- Really Easy
- Less than 15 mins
1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
Was this helpful?
Thank you for voting!
timer knob broken
5 of 8 people
found this instruction helpful.
-
Peggy A from La Place, LA
- Really Easy
- Less than 15 mins
Just put the knob on where old knob was.
Was this helpful?
Thank you for voting!
Lint Filter wore out had to be replace
4 of 5 people
found this instruction helpful.
-
Don from Dayton, TX
- Really Easy
- Less than 15 mins
Changed out the lint filter
Was this helpful?
Thank you for voting!
Frig stopped cooling - Freezer side iced up
6 of 11 people
found this instruction helpful.
-
Walter R from Gainesville, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrost
... Read more
ing properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!
Read less
Was this helpful?
Thank you for voting!
a loud, high-pitched ringing noise
4 of 5 people
found this instruction helpful.
-
Craig from Booneville, AR
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.
Other Parts Used:
Was this helpful?
Thank you for voting!
Clothes took multiple cycles to fully dry.
4 of 5 people
found this instruction helpful.
-
Donald from Pine City, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.
Was this helpful?
Thank you for voting!
small dark lines appearing on clothes
4 of 5 people
found this instruction helpful.
-
James from Ankeny, IA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Like others have descibed, place Dryer on back and remove two hex head screws on back two phillips screws under lint cover, front is "clamped" with two plastic clips that I popped with a standard screwdriver. The door has two screws on the door switch, I removed these although I'm not sure I needed to. Lift the front out of the way. Look
... Read more
at the belt before you remove it, the tensioner pully isn't screwed in place and drops once the belt is removed. It isn't hard to figure out how it goes back together, but you might as well save the swearing. Remove the belt and the drum lifts out. Remove the old seal and glue the new one in place. Another repair suggested clothes pins to hold the seal while it dried, but I opted for some spring clamps with a little more grip. While the seal dries vaccuum the inside of the dryer and vent pipe clean everthing up good by the time you're done the glue is dry. Put the drum back in using a putty knife to slip the seal in place. re assemble in reverse order of disassembly. If I were doing this repair again I would have bought the front seal too. It doesn't appear to get as much wear as the back, but while you have it open why not? Repair easier than expected, but took more time with the cleaning and glue dry time.
Read less
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people
found this instruction helpful.
-
Anthony from PITTSTON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered
... Read more
a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Read less
Was this helpful?
Thank you for voting!
old seal was disintegrating
4 of 5 people
found this instruction helpful.
-
Mike from Vancouver, WA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
As the instructions say: first remove the drum. In the case of my dryer the drum is supported by two rollers on the back panel and the opening in the front panel. Remove the front panel and the drum almost falls out.
Replacing the seal was easy . Just tear out the old seal, lightly sand the rear lip, stretch the new seal ove ... Read more r it, being sure the stitching is oriented properly, and then squeeze adhesive from the supplied tube between the seal and the drum lip.
In putting the dryer back together I couldn't figure out how to thread the belt. I suggest that people attempting this repair take digital pictures of the inside of the appliance before disassembling it.
A very good experience and I prolonged the life of the dryer a good ten more years.
Replacing the seal was easy . Just tear out the old seal, lightly sand the rear lip, stretch the new seal ove ... Read more r it, being sure the stitching is oriented properly, and then squeeze adhesive from the supplied tube between the seal and the drum lip.
In putting the dryer back together I couldn't figure out how to thread the belt. I suggest that people attempting this repair take digital pictures of the inside of the appliance before disassembling it.
A very good experience and I prolonged the life of the dryer a good ten more years.
Read less
Was this helpful?
Thank you for voting!
Lint Filter wore out.
4 of 6 people
found this instruction helpful.
-
Claude from Austin, TX
- Really Easy
- Less than 15 mins
It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.
Was this helpful?
Thank you for voting!
Original timer knob broke and dryer door would not close
3 of 3 people
found this instruction helpful.
-
Gary from ONEKAMA, MI
- Really Easy
- Less than 15 mins
Timer knob.....took new knob out of protective shipping bag and installed it on the existing timer stem. It took less than one minute.
Door catch kit......removed original female latch part from dryer door and installed new one by pushing it in the hole left by the original part.
Door catch kit......removed original female latch part from dryer door and installed new one by pushing it in the hole left by the original part.
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer would not turn on
3 of 3 people
found this instruction helpful.
-
donald from MANVILLE, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
Needed a new lint filter
3 of 3 people
found this instruction helpful.
-
Evelyn from JACKSONVILLE, FL
- Very Easy
- Less than 15 mins
Took the old one out, replaced it with new one.
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people
found this instruction helpful.
-
PHILLIP from AUSTIN, MN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use
... Read more
locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Read less
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people
found this instruction helpful.
-
james from york, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!