1108608 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer motor siezed up, from age and wear
9 of 13 people
found this instruction helpful.
-
S.K. Mechancil Company from Pittsfield, MA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Troubleshhot problem, used multimeter to verify current to motor. Once that i was sure motor was getting proper voltage, I used a meg-ohm meter on A/C motor windings and physically tried to turn motor and found that it was siezed. I then cleaned inside of unit inspected belt and drum rollors. Due to the cost of the items, I decided If I w
... Read more
as going to replace the motor I should replace all moving parts, and install new belt. Everything went easy. WHAT WAS MOST IMPRESSIVE! was that the Parts people sent the correct parts on time the first time, with no hiddin charges. There web site should accurate diagrams of parts and internals of machine. I was really pleased and will use this service again. Thank you
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Door Switch Actuator Spring had broken
8 of 10 people
found this instruction helpful.
-
Norman from Allen, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I took the dryer apart by visually looking at it and removing screws, etc. until I had the top off and the front off. I took the dryer apart so I could get the part out and use it visually ascertain I was ordering the same part.
I bought the replacement part and only then did I have the instructions to take the dryer apart. I ... Read more t was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.
I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.
I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.
I bought the replacement part and only then did I have the instructions to take the dryer apart. I ... Read more t was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.
I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.
I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.
Read less
Was this helpful?
Thank you for voting!
handle broke on filter
7 of 8 people
found this instruction helpful.
-
Connie from Gaithersburg, MD
- Really Easy
- Less than 15 mins
just slide the new filter in.
Was this helpful?
Thank you for voting!
Broken Door Handle on Front of Dryer
13 of 26 people
found this instruction helpful.
-
Jeff from Wausau, WI
- Really Easy
- Less than 15 mins
Do to age and heat the dryer door handle was brittle and broke. Ordering was easy on line. Part was delivered faster tan expected. Oh and the repair time, Less than 1-minute.
Thanks for the great service.
Thanks for the great service.
Was this helpful?
Thank you for voting!
My Kenmore dryer door catch was worn out, so the dryer door wouldn't stay closed, and I was unable to dry my laundry.
8 of 11 people
found this instruction helpful.
-
Carol from Golden Valley, MN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin
... Read more
that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't run
6 of 6 people
found this instruction helpful.
-
Edward from Richlands, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one.
... Read more
Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!
Repair took about five minutes and saved approximately $70!
Repair took about five minutes and saved approximately $70!
Read less
Was this helpful?
Thank you for voting!
broken rib belt
6 of 6 people
found this instruction helpful.
-
Robert from PEABODY, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Wil
... Read more
l be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer making squealing noise.
8 of 12 people
found this instruction helpful.
-
Harriet from Palm Coast, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up.
... Read more
Replaced front and top.
Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer made a terrible squealing noise
7 of 9 people
found this instruction helpful.
-
Will from Charlotte, NC
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.
Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Read less
Was this helpful?
Thank you for voting!
Dryer stopped spinning.
8 of 12 people
found this instruction helpful.
-
sherif from BARTONSVILLE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer runs but, no heat
6 of 6 people
found this instruction helpful.
-
Richard from WAVERLY, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
found a video online and followed the instructions. First unplug dryer, then take off back cover with a 1/4 inch socket unscrew the 5 screws from the cover and remove back. Then with a ohms meter you have to check to see what terminals are bad. In my case it was the heating element. So, next you go to top of dryer and unscrew the lint tra
... Read more
p so you can lift the top of dryer and remove the bracket holding the housing where the element is located. First take off the leads that are connected to the element and housing unit. Then gently lift housing unit up off the hinges and pull it out. Then turn over and there is another screw that holds the heating element in. After unscrewed the element pulls right out and then just put new element in and reverse everything.
Read less
Was this helpful?
Thank you for voting!
Start windings burnt out on original motor (dryer would not start)
7 of 10 people
found this instruction helpful.
-
Frank from Smyrna, TN
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to un
... Read more
thread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
Read less
Was this helpful?
Thank you for voting!
Auto Dry Sensor Failed
9 of 16 people
found this instruction helpful.
-
J from Trabuco Canyon, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.
Was this helpful?
Thank you for voting!
Loud squeeking.
6 of 8 people
found this instruction helpful.
-
John from Alton, IL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench set
I ordered the belt idler pully and drum support rollers and after watching the video on Parts Select web page, changed the parts. It could be done by one person, however having a second person to help with the drum installation worked great. I discovered the motor bearing on the front side of the motor was the source of the squeek. I d
... Read more
isassembled the dryer again and removed the motor. After ordering a motor the installation and reassembly went smoothly. The parts came in two days of placing the orders and virtually new parts in the dryer makes it seem like a new machine.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Door Gasket Came Off The Dryer And Tangled In Clothes
14 of 32 people
found this instruction helpful.
-
Jennifer from Biloxi, MS
- A Bit Difficult
- 15 - 30 mins
I haven't been able to do the repair yet because the door gasket has to be "glued" in and the gasket doesn't come with a sealer of any sort. It is just the rubber ring. I am going to have to go to my local lowe's or home depot and ask someone to help me find what I need to glue the gasket in place. The repair itself should be simple
... Read more
. The gasket just sits in the "groove," but without a sealer of some sort, the gasket will come loose again and I will be back to having a dryer that takes twice as long to dry my clothes.
Read less
Was this helpful?
Thank you for voting!