110847 Kenmore - Instructions

All Instructions for the 110847
46 - 60 of 1424

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Upper agitator stopped moving
38 of 46 people found this instruction helpful.
  • Craig from Yadkinville, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ea rs were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.
Was this helpful?
Thank you for voting!
Leaking water pump where casing halves split.
35 of 37 people found this instruction helpful.
  • David from Washington Crossing, PA
  • Easy
  • 15 - 30 mins
  • Pliers
Replaced pump without disassembling the cabinet or disconnecting motor or any other parts.

Disconnected power, drain, hot and cold water lines. drained lines to pail before taping to top of unit.

Tipped the unit to a 45 Deg. angle, leaning the top side edge onto a stool so that pump presented well at the raised bott om edge.

Removed hose clamps at pump suction and discharge ports and drained water into a shallow soaking pan. Kept clamps on hoses to facilitate reinstallation of pump.

Removed spring clamps at front and rear of pump housing.

Wiggled motor shaft away from coupling in pump. This is a friction fit, so no parts removal was required and no parts "come loose" in the process.

Wiggled new pump housing onto the motor shaft after checking square shaft alignment with respect to square female coupling on pump.

Pushed and twisted hose ends onto pump suction and discharge ports, then pulled spring clamps down over hose ends at pump ports.

Reset spring clamps so that they were aligned and square with pump ports. Reconnected power, drain, hot and cold water line connections.

Washer ran as before but without leaks this time.
Was this helpful?
Thank you for voting!
sounded out of balance even after shifting clothes
35 of 38 people found this instruction helpful.
  • Lori from Parchment, MI
  • Easy
  • 15 - 30 mins
  • Pliers
The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not wo rk properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.
Was this helpful?
Thank you for voting!
dryer works but no heat.
35 of 44 people found this instruction helpful.
  • Tom from Grove, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Measured resistance on thermostats & heating element. Found thermostat open so ordered replacement part and heat again.
Was this helpful?
Thank you for voting!
Excessive tub wobble, tubs leaning forward of normal
31 of 33 people found this instruction helpful.
  • David from GLEN BURNIE, MD
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.

While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.

At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.

Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.
Was this helpful?
Thank you for voting!
unbalanced load...knocking sound.
32 of 37 people found this instruction helpful.
  • Edward from Easthampton, MA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, sc rew). Reassembled washer then ran wash for a cycle. Successful fix.
Was this helpful?
Thank you for voting!
Found cracked brake shoe
33 of 41 people found this instruction helpful.
  • Michael from Trafalgar, IN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, the n used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.
Was this helpful?
Thank you for voting!
Dryer motor runs,drum turns but no heat.
30 of 33 people found this instruction helpful.
  • Arron from El Reno, OK
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed the back of the dryer. Used a multimeter set to read Ohms to check each Thermal cut-off switch. Each one read with continuity and some resistance. The one that was bad read open. So i replaced this one and the other one that came in the kit since i already paid for both.Then i replaced the back ran the dryer and it worked great.
Was this helpful?
Thank you for voting!
push to start switch was not working
33 of 43 people found this instruction helpful.
  • Grace from New Smyrna Beach, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this helpful?
Thank you for voting!
Top door catch assembly had broken
29 of 31 people found this instruction helpful.
  • tony from prineville, OR
  • Easy
  • Less than 15 mins
  • Screw drivers
It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public!
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people found this instruction helpful.
  • Bill from Houston, TX
  • Really Easy
  • Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
Washer would fill/empty but would not agitate nor spin
30 of 35 people found this instruction helpful.
  • Ted from SOUTH MILWAUKEE, WI
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The r ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people found this instruction helpful.
  • Robert from GOODRICH, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel. The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Was this helpful?
Thank you for voting!
Dryer not spinning
33 of 49 people found this instruction helpful.
  • john from goldsboro, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Was this helpful?
Thank you for voting!
dryer ran but no heat
34 of 53 people found this instruction helpful.
  • Mary from Red Bud, IL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench set
I removed the dryer rear upper cover to expose the start and cycle selection knob. My wiring diagram was in there. I removed the wiring on the rear of the cycle selection knob (timer assembly) locations were marked on the device. I ohmed the switch contacts for the heat circuit and had an open circuit through out the full rotation of the knob. I removed the 2 screws on the back of the timer assembly and the burnt contacts fell out. I removed the knob and 2 mounting screws and the device was out to retrieve my part numbers.
Was this helpful?
Thank you for voting!
All Instructions for the 110847
46 - 60 of 1424