110841 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer on/off door switch broke and needed replaced.
8 of 13 people
found this instruction helpful.
-
David from Fort Myers, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Took the dryer top off and removed the bad part. Looked it up online and found a replacement by looking for whirlpool parts. They didn't have one at the local parts stores so I ordered the part online and had it mailed within three days. I replaced it quite easily. It worked and I put everything back together and my wife took over the
... Read more
tricky part of drying the laundry! The repair was quite easy for a non mechanical person like me.
Read less
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people
found this instruction helpful.
-
Betty from Erie, PA
- Really Easy
- 15 - 30 mins
-
Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
Dryer would not heat
6 of 8 people
found this instruction helpful.
-
John from Fort Lauderdale, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed back panel. With the circuit tester I tested the heating coil and the thermostats and the one-time fuse. I found the fuse did not test a circuit. So I ordered the fuse and replaced it. The dryer works fine.
Was this helpful?
Thank you for voting!
lod and heat caused cracks
5 of 6 people
found this instruction helpful.
-
Lawrence from Hull, MA
- Really Easy
- Less than 15 mins
replace basket with new one snapped in
Was this helpful?
Thank you for voting!
incessantly annoyingly squeaky dryer
5 of 6 people
found this instruction helpful.
-
Douglas from Tiburon, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an
... Read more
d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Read less
Was this helpful?
Thank you for voting!
The dryer was squeaking and would not heat at all.
7 of 12 people
found this instruction helpful.
-
Steven from Oxnard, CA
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
5 of 7 people
found this instruction helpful.
-
Dillard C. from Vina, AL
- Easy
- 15 - 30 mins
-
Socket set
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would fill with water but not start
4 of 4 people
found this instruction helpful.
-
LeRoy from OLYPHANT, PA
- Very Easy
- 30 - 60 mins
-
Screw drivers
Moved top control panel and pulled cabnet back changing switch,then reassembled,very easy,don’t forget to un plug
Was this helpful?
Thank you for voting!
The air heater would not heat air to dry on the heat cycle
4 of 4 people
found this instruction helpful.
-
Roger from WEVERTOWN, NY
- Really Easy
- 30 - 60 mins
I misdiagnosed the problem as heater element because I did not have my voltage meter with me. The problem was the heat thermostat that senses temperature in the drum and burns out if it's too high. There are two other safety cut off thermostats that when triggered will reset themselves when the temp cools. All three should be tested be
... Read more
fore looking for something else, like the cycle selector switch; that one is not only more complex but very difficult to access. One is on the heater element itself, the other senses the temperature of air flowing out of the heater element. I believe this array of thermostats is similar on every drier. Each one should be tested with an electrical multifunction tester before guessing what's wrong. The drum thermostat, a $13 part, was the easiest to replace, once I got the back of the drier completely open, a not too difficult task. And, as I found out talking to a repairman, is the thermostat that most commonly fails. I will add that Partselect was most accommodating in providing advice and in authorizing me to return the heater element and refunding the overnight shipping fee. And their web site is terrific--the only drawback being you have to read it over thoroughly before concluding you are an "expert". I would work with them before any other vendors. Good luck!
Read less
Was this helpful?
Thank you for voting!
Old filter and cover had rusted retaining clips and rusted out sections
4 of 4 people
found this instruction helpful.
-
david from HAYWARD, CA
- Very Easy
- Less than 15 mins
Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!
Was this helpful?
Thank you for voting!
Old lent trap replaced with new...
4 of 4 people
found this instruction helpful.
-
Michael from MORGANTOWN, WV
- Easy
- Less than 15 mins
Popped out the old lent trap & popped in the new one..and walla perfect repair..
Was this helpful?
Thank you for voting!
No heat to dryer
6 of 10 people
found this instruction helpful.
-
Karl from Palm Bay, FL
- Easy
- 15 - 30 mins
-
Nutdriver
The failure was located at the back of the dryer behind the back cover. Removal of thr cover was quite easy and the thermal fuse is located completly in the open. Replacement was a snap after conferming that this was the only problem After testing the cover was replaced and the dr
... Read more
yer reinstalled into the original place with no problems.
Read less
Was this helpful?
Thank you for voting!
Stackable dryer wouldn't heat up.
4 of 4 people
found this instruction helpful.
-
Lisa from Prescott, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced the one time use thermal fuse.
Was this helpful?
Thank you for voting!
Dryer continued to run non-stop
5 of 8 people
found this instruction helpful.
-
Gary from Rossville, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Found that when the dryer continued to run after the door was opened that the door switch had gone bad. I unpluged the Dryer, opened the top of the dryer to get access to the switch by lifting top up with fingers and a gentle prying of a flat screwdriver to release spring clips holding it down. I then unplugged the wires from the switch a
... Read more
nd removed the 2 screws that held the switch in. Then reverse this process when you get your new switch from part select (which we received in 2 days) and the total time to fix it took aprox. 10-15 min. total to do. Easy fix for ANY handy person at home!
Read less
Was this helpful?
Thank you for voting!
Gasket was falling off, needed replacement
4 of 6 people
found this instruction helpful.
-
Anthony from N. Ferrisburg, VT
- Really Easy
- Less than 15 mins
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
Was this helpful?
Thank you for voting!