1108318 Kenmore - Instructions

All Instructions for the 1108318
16 - 30 of 266

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My dryer only heats up at the beginning of cycle so my clothes will not dry.
31 of 39 people found this instruction helpful.
  • Monique from Mission Viejo, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this helpful?
Thank you for voting!
no heat
31 of 40 people found this instruction helpful.
  • rex from streator, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this helpful?
Thank you for voting!
Lid closes, switch wouldn't turn on machine.
31 of 47 people found this instruction helpful.
  • Kenneth from Wilmington, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Was this helpful?
Thank you for voting!
dryer stoped heating
23 of 26 people found this instruction helpful.
  • valerie from Elasmore, KS
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this helpful?
Thank you for voting!
No Heat, no ignition in burner
21 of 26 people found this instruction helpful.
  • Russell from Santa Maria, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Our dryer would not heat and it seemed that no gas was coming from the regulator. The igniter was working fine but the burner never turned on. To check the problem, i followed the instructions to remove all body panels until I had access to the burner assembly. I dismantled both gas valve coils and tested each one for open or closed circu it using my multi-tester. I found that the three terminal gas valve coil was an open circuit and was not functioning so I ordered a new one from PartSelect and within just a couple days, had the drier back up and functioning. I also replaced the igniter due to a malfunctioning igniter that has been changed by the manufacture. I must say that PartSelect has the fastest shipping I have ever seen. One part I ordered was at my door in less than 24 hours and I only paid standard shipping...un real! OUTSTANDING....5 STAR SERVICE
Was this helpful?
Thank you for voting!
Would not heat sometimes
21 of 26 people found this instruction helpful.
  • Chris from Laguna Niguel, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.
Was this helpful?
Thank you for voting!
Washer would fill up, wash, then stop
22 of 31 people found this instruction helpful.
  • Glen from Plano, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Was this helpful?
Thank you for voting!
Replaced two parts in the gas heater assembly
20 of 26 people found this instruction helpful.
  • L R from Carmel, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with th e new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Was this helpful?
Thank you for voting!
dryer worked but no heat
18 of 20 people found this instruction helpful.
  • Tracie from Culver City, CA
  • A Bit Difficult
  • 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this helpful?
Thank you for voting!
water pump
25 of 43 people found this instruction helpful.
  • David from Homosassa, FL
  • Really Easy
  • 15 - 30 mins
  • Socket set
replaced
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 people found this instruction helpful.
  • Xiaobin from Cordova, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.
Was this helpful?
Thank you for voting!
Washer will agitate, but won't spin
18 of 24 people found this instruction helpful.
  • Mandie from Lewisville, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.

I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.

The swit ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.

After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.

Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people found this instruction helpful.
  • PHILIP from LONG ISLAND CITY, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people found this instruction helpful.
  • Robert from North East, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people found this instruction helpful.
  • Jerry from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Was this helpful?
Thank you for voting!
All Instructions for the 1108318
16 - 30 of 266