All Installation Instructions for Kenmore Dishwasher 110773812

A spring was broken in the disposal chopper

I bought the kit because it had other parts that I thought I needed.

Parts Used:

Drain and Wash Impeller Kit

Robert from Sherwood, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The upper rotor mount broke off.

I screwed the rack mount to the spindle using
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.

I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.

Parts Used:

Dishwasher Screw

Dishwasher Upper Spray Arm Mount

Middle Spray Arm Kit

George from Wayside, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Part in the lower rack had rusted out

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

Parts Used:

Tine Row

Janet from Hollister, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

SOAP DISPENSER DOOR DID NOT CLOSE.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

Parts Used:

Dishwasher Detergent Lid Spring

Dishwasher Soap Dispenser Cover

Dishwasher Lid Hinge Pin

ROBERT from MAHWAH, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The soap dispenser lid was broken

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

Parts Used:

Dishwasher Soap Dispenser Cover

ed from potomac, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The coating on the upper rack had rust coming through.

Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.

Parts Used:

Dishwasher Upper Dishrack w/Middle Arm And Tube

Ernie from Salinas, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

dish washer leaking

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

Parts Used:

Dishwasher Door Gasket - Gray

Gary from Winnemucca, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

1/4 inch bolt frozen to shaft

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

Parts Used:

Drain and Wash Impeller Kit

Elmer from YORKVILLE, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The hose that connected to the middle spray arm was worn and had deteriorated

Easily installed the hose and replaced the middle spray arm with the help of my brother the savior! Lol. It was very easy for him to install.

Parts Used:

Rinse Aid Cap

Middle Spray Arm Kit

Denise from BRONX, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

broken door spring

Pulled dishwasher out from counter. Took cover off and replaced door springs.

Parts Used:

Spring, Door

David from LEONARDTOWN, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Door leaking water.

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

Parts Used:

Dishwasher Door Gasket - Gray

Jonathan from Henderson, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.

Just removed the old lower dishrack and set in the new one. Nothing to it.

Parts Used:

Lower Dishrack

Richard from Middletown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Broken mount caused dishwasher to shoot water against door, caused leaking

Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.

Parts Used:

Dishwasher Upper Spray Arm Mount