- Home
- 11077122310
- Instructions
11077122310 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
felt strip came off lint screen
223 of 279 people
found this instruction helpful.
-
JEFFREY from FALL RIVER, MA
- Really Easy
- Less than 15 mins
ordered new lint screen, removed old screen, inserted new screen.
Was this helpful?
Thank you for voting!
Felt gasket on lint filter loose...
61 of 71 people
found this instruction helpful.
-
Catherine from Atascadero, CA
- Really Easy
- Less than 15 mins
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 mo
... Read more
nths! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!
Read less
Was this helpful?
Thank you for voting!
Rear tub seal failure
67 of 90 people
found this instruction helpful.
-
Jerry from Everett, WA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the
... Read more
unit...works fine
Read less
Was this helpful?
Thank you for voting!
Gas Flame Would Drop Out
49 of 66 people
found this instruction helpful.
-
FRED from BRIELLE, NJ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this helpful?
Thank you for voting!
worn out part
44 of 64 people
found this instruction helpful.
-
John from Tucson, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Other Parts Used:
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people
found this instruction helpful.
-
Robert from GOODRICH, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel.
... Read more
The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Read less
Was this helpful?
Thank you for voting!
Felt piece coming out of filter
27 of 33 people
found this instruction helpful.
-
Sara from Solon, IA
- Really Easy
- Less than 15 mins
Removed old filter and put in new one.
Was this helpful?
Thank you for voting!
Dryer would not heat up.
26 of 30 people
found this instruction helpful.
-
Roger from Bonners Ferry, ID
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the f
... Read more
ront open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Read less
Was this helpful?
Thank you for voting!
noisy drum
29 of 40 people
found this instruction helpful.
-
Jeff from Mesa, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
Dyer would not heat, flame would shut off within 10 seconds
24 of 29 people
found this instruction helpful.
-
Christy from Riley, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Was this helpful?
Thank you for voting!
Poorly designed lint filter/ gasket falls off
25 of 34 people
found this instruction helpful.
-
John from Madison, WI
- Really Easy
- Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
Heat Would Not Come On
20 of 24 people
found this instruction helpful.
-
Lynn from Novi, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lo ... Read more t of time and money if I had read that earlier.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lo ... Read more t of time and money if I had read that earlier.
Read less
Was this helpful?
Thank you for voting!
The felt strip on the filter had come undone.
21 of 31 people
found this instruction helpful.
-
Rebecca from Laredo, TX
- Really Easy
- Less than 15 mins
Took the old filter out and inserted the new one- works great!!
Was this helpful?
Thank you for voting!
parts took more than two months to get here.
17 of 19 people
found this instruction helpful.
-
rodney from Mad River, CA
- Very Difficult
- More than 2 hours
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Other Parts Used:
Was this helpful?
Thank you for voting!
seal for lint filter came off
17 of 23 people
found this instruction helpful.
-
John from Midland, TX
- Really Easy
- Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!