11077122310 Kenmore Dryer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Drum Support Roller – Part Number: WPW10314173
$28.21
In Stock
Dryer Drum Support Roller
★★★★★
★★★★★
(15)
Part #WPW10314173
This genuine OEM dryer drum support roller is designed to hold the drum in place while allowing it to rotate smoothly and quietly during operation. Built for durability and reliable performance, it helps reduce noise and ensures consistent tumbling. Ideal for replacing worn or damaged rollers, it resolves issues such as squeaking, rumbling, or poor drum movement, helping restore efficient and dependable dryer operation.
Lint Filter – Part Number: W10120998
$62.65
In Stock
Lint Filter
★★★★★
★★★★★
(68)
Part #W10120998
This dryer lint filter is designed to capture lint and debris during the drying cycle, helping maintain airflow and prevent potential fire hazards. Measuring approximately 12.5 inches wide by 10.5 inches deep, it fits securely into the designated slot within compatible dryer models. Regular inspection and replacement of the filter are essential for optimal performance. Installation is tool-free—simply remove the old filter and insert the new one. During replacement, it's recommended to check the filter slot for any accumulated lint, which should be cleared to ensure safe and efficient operation.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Dryer Drum Seal with Adhesive – Part Number: 280114
$61.07
In Stock
Dryer Drum Seal with Adhesive
★★★★★
★★★★★
(29)
Part #280114
This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.
Outlet Screen Door Grille – Part Number: W11086603
$41.95
In Stock
Outlet Screen Door Grille
★★★★★
★★★★★
(16)
Part #W11086603
Protect your clothes and keep your dryer running smoothly with this replacement screen door grille. As the top cover for the lint filter, it helps prevent snags and supports proper airflow. If your current grille is cracked or broken, it could lead to damaged clothing or reduced drying performance. This plastic cover is sold individually and does not come with mounting screws, so be sure to check your existing setup before ordering.
Dryer Radiant Flame Sensor – Part Number: WP338906
$49.45
In Stock
Dryer Radiant Flame Sensor
★★★★★
★★★★★
(6)
Part #WP338906
This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.
Air Conditioner Cover Screw – Part Number: WP308685
$10.95
In Stock
Air Conditioner Cover Screw
Part #WP308685
Sold individually.
Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272 – Part Number: WPW10359272
$65.95
In Stock
Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272
★★★★★
★★★★★
(3)
Part #WPW10359272
Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.
Screw - 10-16 x 1 – Part Number: WP3387230
$10.44
In Stock
Screw - 10-16 x 1
★★★★★
★★★★★
(2)
Part #WP3387230
This screw is sold individually.
Drum Support Roller Shaft - Right Hand Threads – Part Number: WPW10359271
$65.95
In Stock
Drum Support Roller Shaft - Right Hand Threads
Part #WPW10359271
This shaft is for the front with right hand thread. Sold individually.
Dryer Thermal Cutoff – Part Number: WP8573713
$71.45
In Stock
Dryer Thermal Cutoff
Part #WP8573713
The thermal cut off fuse will disrupt the power flow to the drive motor when the dryer gets too hot. If your dryer will not heat properly, or will not heat at all the issue could be with a faulty or damaged thermal cut off fuse. Before you replace the faulty cut off fuse, make sure you disconnect the power from your dryer.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.

Common Symptoms of the 11077122310

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
felt strip came off lint screen
223 of 279 people found this instruction helpful.
  • JEFFREY from FALL RIVER, MA
  • Really Easy
  • Less than 15 mins
ordered new lint screen, removed old screen, inserted new screen.
Was this helpful?
Thank you for voting!
Felt gasket on lint filter loose...
61 of 71 people found this instruction helpful.
  • Catherine from Atascadero, CA
  • Really Easy
  • Less than 15 mins
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 mo nths! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!
Was this helpful?
Thank you for voting!
Rear tub seal failure
67 of 90 people found this instruction helpful.
  • Jerry from Everett, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine
Was this helpful?
Thank you for voting!