110770 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat sometimes, But for a moment then None
4 of 4 people
found this instruction helpful.
-
Scott from Sacramento, CA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i d
... Read more
ecided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.
Read less
Was this helpful?
Thank you for voting!
Very loud squeaking noise
5 of 7 people
found this instruction helpful.
-
Philip from CHICAGO, IL
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
Was this helpful?
Thank you for voting!
My dryer was squeaking with an occasional thump
4 of 4 people
found this instruction helpful.
-
Michael from BOILING SPGS, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench set
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people
found this instruction helpful.
-
Paul from STONE CREEK, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Sqeeking noise fron old worn belt and rollers
4 of 4 people
found this instruction helpful.
-
Randy from HUNTSVILLE, AL
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this helpful?
Thank you for voting!
No heat...
5 of 7 people
found this instruction helpful.
-
Charles from Long Beach, CA
- Easy
- 30 - 60 mins
-
Socket set
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this helpful?
Thank you for voting!
Blower belt came loose, but didn't snap. It was old and perhaps brittle.
4 of 4 people
found this instruction helpful.
-
Gabe from Tulsa, OK
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
First, lift top by pushing in the 2 locking clips ( with the dryer door open), otherwise it won't lift.
Secondly, remove front cover by taking out 2 screws easily seen . If you see any electrical connectors, remove them.
Only thing a bit nightmarish was installing the new belt. It didn't seem long enough even though it was the ... Read more original exact replacement. I got hair dryer blower, used on belt for 30 seconds, and mission accomplished.
Secondly, remove front cover by taking out 2 screws easily seen . If you see any electrical connectors, remove them.
Only thing a bit nightmarish was installing the new belt. It didn't seem long enough even though it was the ... Read more original exact replacement. I got hair dryer blower, used on belt for 30 seconds, and mission accomplished.
Read less
Was this helpful?
Thank you for voting!
change from nat . LP gas.
7 of 14 people
found this instruction helpful.
-
William from Afton, OK
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Remove top then front panel kit goes on gas value 2 screws hold gas tube in place.
Was this helpful?
Thank you for voting!
LP conversion kit
8 of 17 people
found this instruction helpful.
-
Steve from Brunswick, VT
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate m
... Read more
y snap ring pliers(just moved). The directions were spot on, read them through once before you start.
Read less
Was this helpful?
Thank you for voting!
Dryer heat would go off and timer would not move. Dryer would continuously run
4 of 5 people
found this instruction helpful.
-
chuck from smithtown, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Replaced coils on gas valve.
Was this helpful?
Thank you for voting!
would only heat for about 7 minutes.
4 of 5 people
found this instruction helpful.
-
Craig from ARMA, KS
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I replaced the thermos fuse, thermostat, igniter kit, and the M series
new style coil kit. The problem was the M series coil kit. I replaced
the other parts because this dryer is over 10 years old. I also brought
the radiant flame sensor. I spent $126.19 in parts plus shipping. If I just
just replaced the coil kit it ... Read more would have 18.61 plus shipping. A new gas dryer like I have would cost about $459.00. I hope to get many more years out of this dryer. The hardest part of this repair for me was getting the front panel back on. I saved the parts that were good for futher repairs. I replaced the drum belt several years ago, still looks in good shape. I think this is a great DIY site. Just follow their instrutions. Somtimes I'll take a picture of the part before I remove it, just to be sure I replace it right.
new style coil kit. The problem was the M series coil kit. I replaced
the other parts because this dryer is over 10 years old. I also brought
the radiant flame sensor. I spent $126.19 in parts plus shipping. If I just
just replaced the coil kit it ... Read more would have 18.61 plus shipping. A new gas dryer like I have would cost about $459.00. I hope to get many more years out of this dryer. The hardest part of this repair for me was getting the front panel back on. I saved the parts that were good for futher repairs. I replaced the drum belt several years ago, still looks in good shape. I think this is a great DIY site. Just follow their instrutions. Somtimes I'll take a picture of the part before I remove it, just to be sure I replace it right.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people
found this instruction helpful.
-
Gregory from COCOA, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
The dryer would not heat up
4 of 5 people
found this instruction helpful.
-
William from Canyon Country, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...
Was this helpful?
Thank you for voting!
Too much drying time, not hot enough
4 of 5 people
found this instruction helpful.
-
John from Floyd, VA
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also w
... Read more
hen it arrives.
Good trouble shooting information.
Good trouble shooting information.
Read less
Was this helpful?
Thank you for voting!
Dryer would shut off mid way through cycle and give an E1 error code
5 of 9 people
found this instruction helpful.
-
Dwayne from Bainbridge, PA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back
... Read more
together in reverse. I also took the time to clean any dust and lint out.
Read less
Was this helpful?
Thank you for voting!