110770 Kenmore Dryer - Instructions

All Instructions for the 110770
91 - 105 of 514

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door catch will no longer secure the door close
6 of 6 people found this instruction helpful.
  • Gregory from Carlsbad, CA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pliers and screw driver to pop out the old door catch and pop in the new one. Saved $69.95 service charge for a tech to come to the home.
Was this helpful?
Thank you for voting!
Broken door latch
6 of 6 people found this instruction helpful.
  • William from ROCK ISLAND, IL
  • Very Easy
  • Less than 15 mins
  • Pliers
Followed video instructions using flat scraper & pliers (easy).Tried to remove "SPARE" latch on other side of door. Even removed door myself (Easy).Tried for (45) minutes without success. Ordered part @ 11:30 pm. Replaced door easily by myself by leaving bottom screw for each hinge in place & replaced broken latch. Received new latch in (5) days. Removed broken latch without tools & replaced new latch in (15) seconds. Need help from any "Ladies" who can remove second latch so it is available for next replacement. This "Engineer" was too lazy to remove the screws around the door because he was going to "Follow the Video". Overall it was an "Easy Fix". Keep the 'Videos"coming.
Was this helpful?
Thank you for voting!
Lens melted because paper got behind the lens and was heated by the lamp.
6 of 6 people found this instruction helpful.
  • Chris from Valley Stream, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1 screw to replace.
Was this helpful?
Thank you for voting!
Dryer would run 1 min then stop running with some heat in drum
10 of 18 people found this instruction helpful.
  • Bob from CHULA VISTA, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Videos are excellent to open and access internal parts. It turned out a rat was killed in the blower fan when we first encountered the problem. This prevented the blower from turning which interfered with motor function.

This required removing drum & belt, disconnecting motor clips, blower belt, and blower housing. The blower housing needed to be disassembled. Having a 5/16” & 1/8” ratcheting nut driver makes this process much easier. Don’t try this with a wrench.

After getting rid of the rat and decomposition, we sanitized the entire housing with soap & chlorine bleach.

Reassembly was uneventful and relatively easy. We ended up replacing 4 rollers, 2 belts (drum belt & blower belt), the thermistor which was damaged as a result of the blocked blower.
Was this helpful?
Thank you for voting!
Idler pulley squeaking very badly
6 of 6 people found this instruction helpful.
  • Andy from DAGGETT, MI
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took back panel of dryer off completely disconnected the drive belt to drum of dryer took off old idler pulley reinstall the new pulley and belt works like a brand new dryer
Was this helpful?
Thank you for voting!
Gas would not turn on after around 10 minutes of "normal" operation.
6 of 6 people found this instruction helpful.
  • Carmen from HOWELL, MI
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
I've nothing to add to the techniques already described in the other narratives except that the dryer operated normally at first, but then after around 10 minutes the flame no longer cycled. I suspected a bad high limit thermostat since the valves seemed to be working. I ordered the replacement coils only because they were listed as the most common thing to fail. After replacing the T-Stat there was no change; I started checking things w/ a multimeter and found that all the T-Stats were closed. I should have done that at first. Anyway, since I had the new coils I decided to put them in. The dryer has workd perfectly ever since. Lesson to be learned: the coils may check ok when cold, but become inoperable after heating up a bit.
Was this helpful?
Thank you for voting!
Felt that lines the edges of the drum had degraded from the side nearest the door.
6 of 6 people found this instruction helpful.
  • Chris from DAYTON, OH
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
I was not able to find a video (or other specific instructions) that showed how to access the insides of this particular machine, but eventually figured out that all it takes is popping 2 clips, one on either side of the door by wedging a flathead screwdriver in the space between the top of the machine and the bottom piece that surrounds the door opening. The top then pivots up and can be moved back beyond vertical so that it hold itself in position.

After removing the dryer door, getting to the drum itself was not too difficult and only involves removing half a dozen small bolts. I was able to move the pieces off to the side without disconnecting any of the wiring. Without looking at the parts diagram I can't name any of the pieces involved, but there were only a couple. The drum can then be lifted right off its rollers.

The replacement felt for this dryer has to be fastened with adhesive, and I would recommend running the bead of glue around half of the drum, setting the new felt in place, letting it sit for a few minutes to let the glue set up, then repeating for the other half. I tried installing the entire piece of felt at once, but after getting about 3/4 of it on, pulling the remaining unattached felt taut to fit around the drum ended up removing the first part of the felt because the glue did not have time to set up. If you've ever changed a bicycle tire, you'll know about reaching that point where the tire doesn't seem big enough to fit around the rim, but it just needs to be muscled into place. Same idea here, but trying to muscle the felt over fresh glue while the just installed part comes loose is frustrating and in my case almost resulted in ruining the entire new felt strip. Once the felt is anchored it's easy to pull taut over the remaining part of the drum.
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people found this instruction helpful.
  • Ken from Bixby, OK
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Was this helpful?
Thank you for voting!
High pitch noice
8 of 13 people found this instruction helpful.
  • Luis from FRESNO, CA
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
Raised the front of top panel with the putty knife and the front panel was unscrewed as the video showed. The drum slid out after the belt was released.

My machine had 4 rollers, which was not shown in the schematics. So I replaced the back, cleaned the front ones and works great for now. Plan to replace the front later. ... Read more />
Removing the tri rings is much easier if cut w wire cutters. Otherwise waist lots of time to get them off. Just buy new ones.
Was this helpful?
Thank you for voting!
Dryer got hot then heat would shut off
6 of 7 people found this instruction helpful.
  • Douglas from Fernley, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and r everse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Was this helpful?
Thank you for voting!
Convert New Dryer to Propane from Natural Gas
9 of 16 people found this instruction helpful.
  • Teri from Bakersfield, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
1.Unplugged the connections to dryer door
2. Removed dryer door, front cabinet,popped off the drum belt (this is done by feel),unplugged the drum from cabinet, removed drum, all to get to the gas element inside at the bottom of dryer.
3. Unplugged the connection to the element, then removed unit to get to the burner parts. ... Read more >4. Replaced the natural gas burner element with the LP gas element.
5. Re assembled dryer and tested.
*Note: Actually my son did the work while I read the very easy to follow directions. Since neither of us has disassembled a dryer before, the thought of taking a brand new dryer all apart was more daunting than the actual task.
Was this helpful?
Thank you for voting!
the factory door catch punched out
8 of 13 people found this instruction helpful.
  • phillip from evansville, IN
  • Really Easy
  • Less than 15 mins
new part came in a day or two. took part out of package and it easly snaped in place. very nice
Was this helpful?
Thank you for voting!
not heat
7 of 10 people found this instruction helpful.
  • Sarah from Merrimac, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on t he tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.
Was this helpful?
Thank you for voting!
Tub seals were out , major clean up!..
6 of 7 people found this instruction helpful.
  • Wilson J from BOERNE, TX
  • Very Easy
  • More than 2 hours
  • Nutdriver
Tear down , pulled drum, rollers, belts. These machines are very simple and very reliable!. I love these machines, they are one of the easiest to work on of any machine l have worked on. I have been a mechanic all my life!.Maytag got it right , their washers are as easy to work on as their dryers!..Very, Very simple..
Was this helpful?
Thank you for voting!
No heat, would not light because igniter burnt out
6 of 8 people found this instruction helpful.
  • anthony from Port Arthur, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Was this helpful?
Thank you for voting!
All Instructions for the 110770
91 - 105 of 514