1107694 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer worked but no heat
18 of 20 people
found this instruction helpful.
-
Tracie from Culver City, CA
- A Bit Difficult
- 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem
... Read more
was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Read less
Was this helpful?
Thank you for voting!
Replaced two parts in the gas heater assembly
20 of 26 people
found this instruction helpful.
-
L R from Carmel, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with th
... Read more
e new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer drum was not turning when started.
17 of 18 people
found this instruction helpful.
-
Dennis from AUSTIN, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I moved the dryer to a location where I could get to both the front and back sides. I opened the back by first removing the top cover and then the back. It requires either a Phillips head screwdriver or a quarter inch socket. In addition, it requires removing the four power wires which connect to the computer. If you are unfamiliar with t
... Read more
he wiring layout, take a photo with your cell phone which you can then refer to when re-assembling. Once the back was removed, I saw that the belt was still intact, but the pulley which provides tension to the belt was frozen. Take a photo of the belt route between the motor and the pulley. Try to get the spring position in the photo. Remove the belt from the pulley by reducing the tension and then sliding the belt out (this assumes the belt is not broken). The pulley arm is held in place by a single bolt which can be removed by a socket set. Remove the arm with the pulley attached. Examine the pulley to figure out why it is frozen. In my case, the pulley had been frozen for some time and the belt had actually chewed through the pulley and was sliding (polishing) on the pulley axle? I used a pair of pliers to loosen the destroyed pulley by rotating it back and forth over the axle while gripping the arm the axle is attached to. As it loosened up I worked it off the axle. I used a cloth to clean the axle of grime from the belt, pulley, and dryer lint. The new pulley comes with a washer and triangular plastic "fastener". First you put on the washer, then the pulley and then you secure it on the axle by sliding the triangular fastener over the axle so it sits in a small grove near the end of the axle. Then put the pulley arm back by replacing the bolt. Make sure you do not overtighten the arm since it is intended to rotate about the bolt. If the dryer belt breaks, the spring will pull the arm down and throw a cutoff switch. Its operation should be obvious. Once the arm is back in place, refer to your photo and replace the spring (this can be tricky and frustrating, particularly if you don't use something like needle nose pliers). Once the spring is in place, depress it and re-install the dryer belt. Refer to the photo you took earlier if you've forgotten how the belt was routed. Then re-install the dryer's back panel, re-attach the electric wires (again refer to the photo you took earlier), and re-attach the top cover. You might want to test your handiwork at this point before you reconnect the dryer vent
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
idler pully sqwieling
19 of 24 people
found this instruction helpful.
-
Jerry Duty from Fort Walton Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!
and your done !!!
Was this helpful?
Thank you for voting!
Broken push to stat switch
18 of 21 people
found this instruction helpful.
-
Charles from Fairfax, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed back cover, removed broken switch, replaced with new switch, replaced back cover, told wife her dryer was fixed.
Was this helpful?
Thank you for voting!
dryer not working
22 of 33 people
found this instruction helpful.
-
Maura from Newtown, CT
- Really Easy
- Less than 15 mins
After unplugging and removing the back cover from the dryer, locate the push button switch. Slide putty knife around outer cover to unhook catch. Replace with new push button switch. My dryer is still not working, but this was a simple replacement.
Was this helpful?
Thank you for voting!
parts took more than two months to get here.
17 of 19 people
found this instruction helpful.
-
rodney from Mad River, CA
- Very Difficult
- More than 2 hours
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Other Parts Used:
Was this helpful?
Thank you for voting!
The felt strip on the filter had come undone.
21 of 31 people
found this instruction helpful.
-
Rebecca from Laredo, TX
- Really Easy
- Less than 15 mins
Took the old filter out and inserted the new one- works great!!
Was this helpful?
Thank you for voting!
Dryer continued to run with door open
18 of 23 people
found this instruction helpful.
-
Colleen from CAPE CORAL, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people
found this instruction helpful.
-
Lynne from Jamestown, CA
- Really Easy
- Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c
... Read more
ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Read less
Was this helpful?
Thank you for voting!
seal for lint filter came off
17 of 23 people
found this instruction helpful.
-
John from Midland, TX
- Really Easy
- Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!
Loud sreeching and vibration
14 of 15 people
found this instruction helpful.
-
Robert from TUTTLE, OK
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are
... Read more
pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people
found this instruction helpful.
-
PHILIP from LONG ISLAND CITY, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people
found this instruction helpful.
-
Kim K from Hurst, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do
... Read more
the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Read less
Was this helpful?
Thank you for voting!
Timer would not move, leaving dryer running
14 of 16 people
found this instruction helpful.
-
John from Lockport, NY
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed screws from back panel. Removed two scews from timer. Disconnected one wire at a time and transfered to new timer until all wires were transfered. Reattached new timer and reattached back panel.
Was this helpful?
Thank you for voting!