1107694 Kenmore Dryer - Instructions

All Instructions for the 1107694
61 - 75 of 1244

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer stoped heating
23 of 26 people found this instruction helpful.
  • valerie from Elasmore, KS
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this helpful?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
44 of 91 people found this instruction helpful.
  • Mark from San Diego, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this helpful?
Thank you for voting!
Poorly designed lint filter/ gasket falls off
25 of 34 people found this instruction helpful.
  • John from Madison, WI
  • Really Easy
  • Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
Dryer Would not start
23 of 29 people found this instruction helpful.
  • Heath from YORK, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Repair was easy after identifying the problem. Parts select was correct with the 3 parts for trouble shooting. However I should have looked at the door switch 1st. Ordered a thermostat and On switch 1st. Then had to reorder the door switch. In the future just order all 3 to avoid the shipping charges and return what you don't need to save time and money.
Was this helpful?
Thank you for voting!
No heat
27 of 42 people found this instruction helpful.
  • Jaime from Chantilly, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all ot her possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.
Was this helpful?
Thank you for voting!
Dryer working but drum light not working, bulb ok.
22 of 27 people found this instruction helpful.
  • Denton from Indianapolis, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as ne eded and tested light by opening door. Works great.
Was this helpful?
Thank you for voting!
The Dryer Would Not Turn On
19 of 19 people found this instruction helpful.
  • Ribhe from Wildwood, MO
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about t wo days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
Was this helpful?
Thank you for voting!
Would not heat sometimes
21 of 26 people found this instruction helpful.
  • Chris from Laguna Niguel, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.
Was this helpful?
Thank you for voting!
Idler Pulley broke
21 of 26 people found this instruction helpful.
  • Keith from Richmond, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
Was this helpful?
Thank you for voting!
No Heat, no ignition in burner
21 of 26 people found this instruction helpful.
  • Russell from Santa Maria, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Our dryer would not heat and it seemed that no gas was coming from the regulator. The igniter was working fine but the burner never turned on. To check the problem, i followed the instructions to remove all body panels until I had access to the burner assembly. I dismantled both gas valve coils and tested each one for open or closed circu it using my multi-tester. I found that the three terminal gas valve coil was an open circuit and was not functioning so I ordered a new one from PartSelect and within just a couple days, had the drier back up and functioning. I also replaced the igniter due to a malfunctioning igniter that has been changed by the manufacture. I must say that PartSelect has the fastest shipping I have ever seen. One part I ordered was at my door in less than 24 hours and I only paid standard shipping...un real! OUTSTANDING....5 STAR SERVICE
Was this helpful?
Thank you for voting!
Moisture sensors need replacement
20 of 24 people found this instruction helpful.
  • Jack from JONESBORO, AR
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in h andy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
Was this helpful?
Thank you for voting!
Heat Would Not Come On
20 of 24 people found this instruction helpful.
  • Lynn from Novi, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lo t of time and money if I had read that earlier.
Was this helpful?
Thank you for voting!
The sensor would not slide into grill
18 of 18 people found this instruction helpful.
  • sandra*broadnax from BRISTOW, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
Initially, i watched the how to do it instruction in the fix website to determine the complexity of repairs. The instruction built up my confidence. I ordered and recieved the grill amd the two new sensors. I placed the two new sensors into the new grill sensor slots. Then removed the old grill by unscrewing three screws. Connected th e two sensors positioned the grill and screwed in the three screws put the lent stray in the grill and closed the dyer door. I have been a happy camper ever since. I saved the $75 home insurance fee plus maintenence installment. Thanks
Was this helpful?
Thank you for voting!
dryer would not turn on
20 of 25 people found this instruction helpful.
  • harley from north lauderdale, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your we bsite and the promt efficient service
Was this helpful?
Thank you for voting!
Replaced two parts in the gas heater assembly
20 of 26 people found this instruction helpful.
  • L R from Carmel, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with th e new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Was this helpful?
Thank you for voting!
All Instructions for the 1107694
61 - 75 of 1244