11076002011 Kenmore Dryer - Instructions

All Instructions for the 11076002011
16 - 30 of 864

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No heat to dry clothes
66 of 77 people found this instruction helpful.
  • Karen from Pine Mtn. Club,, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First I took the front of the dryer off then located the igniter. It only required removing two screws, removing old igniter, replacing with new igniter, and replacing the two screws.. While I was replacing the igniter I took the drum out and throughly cleaned the inside. Lucky me, I found 85 cents on the floor of the dryer. I am 65yr s old, married and mother of two.
This was easy to do and sure saved money. I reccommend others try to do repairs for themselves and using PartSelect was less expensive too.
Was this helpful?
Thank you for voting!
broken belt
66 of 78 people found this instruction helpful.
  • Larry from exeter, RI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First I removed back and top of dryer, then the support braces holding the drum, after that I took the drum out and the blower covers and cleaned the whole dryer of lint and other debris. Installed the new belt and then reassembled the dryer.
Was this helpful?
Thank you for voting!
Broken Switch Assembly
90 of 153 people found this instruction helpful.
  • Michael from Dearborn, MI
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
This was my first dryer repair, and it was so easy. Simply pull out the lint trap and unscrew the two screws that are exposed. They attach the top deck of the dryer to the drum.

Once it's unscrewed, pull forward while lifting the top of the dryer. The top is attached to the control assembly. They should both lift up, but you'll need something to prop it up like you would the hood of your car.

Next, use the pliers to pinch the connector so that you can separate the two parts of the connector.

Open the dryer door to gain access to the screws that hold the switch in place. Use your screwdriver to unscrew the switch.

Plug the new switch connector in, and close up the dryer.

Word of caution; there are sharp edges inside the dryer so be careful.
Was this helpful?
Thank you for voting!
Felt gasket on lint filter loose...
61 of 71 people found this instruction helpful.
  • Catherine from Atascadero, CA
  • Really Easy
  • Less than 15 mins
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 mo nths! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!
Was this helpful?
Thank you for voting!
Rear tub seal failure
67 of 90 people found this instruction helpful.
  • Jerry from Everett, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people found this instruction helpful.
  • RONALD from SALMON, ID
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!
Our dryer started squealing and would then stop running.
55 of 69 people found this instruction helpful.
  • Kelly from Aptos, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.

I input the number into the search box and there was the exact motor I needed.

The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.

The par t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.

I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.

I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.

I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!

Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.

It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!

Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
Was this helpful?
Thank you for voting!
the dryer only blew cold air
48 of 52 people found this instruction helpful.
  • charles from waukesha, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
Was this helpful?
Thank you for voting!
Dryer motor would not turn on
51 of 69 people found this instruction helpful.
  • John from Bluffton, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
Was this helpful?
Thank you for voting!
TOb stopped turning after a week or so of high pitched "squeals" coming from inside the dryer.
43 of 48 people found this instruction helpful.
  • Robert from Princeton, WV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.
Was this helpful?
Thank you for voting!
Gas Flame Would Drop Out
49 of 66 people found this instruction helpful.
  • FRED from BRIELLE, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this helpful?
Thank you for voting!
No power
45 of 55 people found this instruction helpful.
  • Nick from Brandon, FL
  • Easy
  • 1- 2 hours
  • Nutdriver
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.
Was this helpful?
Thank you for voting!
worn out part
44 of 64 people found this instruction helpful.
  • John from Tucson, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people found this instruction helpful.
  • Bill from Houston, TX
  • Really Easy
  • Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people found this instruction helpful.
  • Robert from GOODRICH, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel. The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Was this helpful?
Thank you for voting!
All Instructions for the 11076002011
16 - 30 of 864