11076002011 Kenmore Dryer - Instructions

All Instructions for the 11076002011
61 - 75 of 864

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Defective Door Switch
12 of 13 people found this instruction helpful.
  • George from Bedford, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I a m 80 years old). Your video is great. Gives step by step instructions.
Was this helpful?
Thank you for voting!
Dryer door switch
12 of 13 people found this instruction helpful.
  • Frank from STANFORDVILLE, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
We watched the video on ur website! Thank you
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people found this instruction helpful.
  • William from Pontiac, MO
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people found this instruction helpful.
  • Joyce from Holbrook, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
Dryer Would Not Start.
11 of 13 people found this instruction helpful.
  • GALEN from NEDERLAND, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy a s the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.
Was this helpful?
Thank you for voting!
dryer would not turn off when the door is open
10 of 10 people found this instruction helpful.
  • James from Webster, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
it took loess than 10 minutes to change the door switch after watching the repair video
Was this helpful?
Thank you for voting!
would not stop when opening door during cycle
10 of 11 people found this instruction helpful.
  • PHILIP from MATTHEWS, NC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.
Was this helpful?
Thank you for voting!
Door switch was broken
11 of 14 people found this instruction helpful.
  • Anthony from Orlando, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
Door handle had shattered
9 of 9 people found this instruction helpful.
  • Fred from BRADENTON, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Removed the door after some trial and error attempts. Door handle should come with instructions. Nothing but the handle was in the package. YouTube videos did not cover this model.
Remove the screws holding the hinges to the door, one on each hinge. Pull the door straight up from the hinges. Be careful, the hinges have springs that s hut the door. Once the door is off, remove the screws around the four edges. Separate the front from the inside of the door. Set the inside of the door aside. Remove the flanged nuts from the inside of the door. There may be other screws to remove and save. Save the nuts for reinstallation.
Remove the handle. Replace with the new handle and reuse the flanged nuts and screws to install the handle. Reassemble the door (there may be a piece of cardboard inside for sound proofing) and slide it back onto the hinges. Replace hinge screws. Walla, you’re done.
Was this helpful?
Thank you for voting!
burnt out bulb and broken switch
12 of 19 people found this instruction helpful.
  • fanny from madison, WI
  • Easy
  • Less than 15 mins
  • Screw drivers
Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very ha ppy customers.
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people found this instruction helpful.
  • Larry from HICKORY, NC
  • Very Easy
  • Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this helpful?
Thank you for voting!
All Instructions for the 11076002011
61 - 75 of 864