110712 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Got heat only on start of cycle and no repeat of flame. Suspected coils on gas valve.
18 of 20 people
found this instruction helpful.
-
John T Lundy from Pittsburgh, PA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
I used a multi meter to find coils failed in warmed temperature condition.
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat. ... Read more
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat. ... Read more
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer worked but no heat
18 of 20 people
found this instruction helpful.
-
Tracie from Culver City, CA
- A Bit Difficult
- 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem
... Read more
was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Read less
Was this helpful?
Thank you for voting!
dryer sounded like I was strangling a dog
18 of 21 people
found this instruction helpful.
-
Lynda from Syracuse, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Pie
... Read more
ce of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
Read less
Was this helpful?
Thank you for voting!
dryer had no heat, all other functions worked
20 of 28 people
found this instruction helpful.
-
Bryan from west valley city, UT
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
After replacing the heat element as a guess, (which did not fix it), I measured voltage with a DVOM, found lower cut off switch in op, And thanx to some tips on parts select I ordered the the Thermal cut off kit, fast shipping, installed very easily and all is working properly
Other Parts Used:
Was this helpful?
Thank you for voting!
Squeaky Dryer
17 of 19 people
found this instruction helpful.
-
Daniel from Hamilton, OH
- Easy
- 15 - 30 mins
-
Screw drivers
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
Was this helpful?
Thank you for voting!
Dryer continued to run with door open
18 of 23 people
found this instruction helpful.
-
Colleen from CAPE CORAL, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this helpful?
Thank you for voting!
Loudly clunking clothes drum due to worn out roller
17 of 20 people
found this instruction helpful.
-
KENNETH from WEST ORANGE, NJ
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Followed video on Parts Select site for comparable model showing roller and drive belt replacement.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer kept spinning when the door opened
16 of 18 people
found this instruction helpful.
-
Gary from Ocean Springs, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
Came to Parts Select. Looked for door switch. Read what other people did. Part came in a few days took a few minutes to take old switch out (had to pry the plastic connection apart with little thin screwdriver). Everything was easy
Was this helpful?
Thank you for voting!
part number was different from the original, but it fit just fine.
20 of 30 people
found this instruction helpful.
-
John from Bristol, CT
- Easy
- Less than 15 mins
installed the new dryer lint screen, it fit perfectly
and is now in operation.
and is now in operation.
Was this helpful?
Thank you for voting!
Rear Drum Seal started to come apart
16 of 18 people
found this instruction helpful.
-
Brett from CRESCENT CITY, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Used the YouTube video sent by this site
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint screen torn
15 of 16 people
found this instruction helpful.
-
James from Glenside, PA
- Really Easy
- Less than 15 mins
Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people
found this instruction helpful.
-
Lynne from Jamestown, CA
- Really Easy
- Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c
... Read more
ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Read less
Was this helpful?
Thank you for voting!
Change dryer belt
15 of 17 people
found this instruction helpful.
-
Scott from Bayport, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I p
... Read more
opped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people
found this instruction helpful.
-
PHILIP from LONG ISLAND CITY, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Loud banging noise when running dryer
15 of 18 people
found this instruction helpful.
-
Joseph from Prospect Park, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.
Other Parts Used:
Was this helpful?
Thank you for voting!