110694 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replaced heating element in my dryer
38 of 51 people
found this instruction helpful.
-
Marlene from Indianapolis, IN
- Really Easy
- Less than 15 mins
-
Socket set
I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)
Was this helpful?
Thank you for voting!
Dryer stopped tumbling
34 of 40 people
found this instruction helpful.
-
Clifford from Mastic, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum
... Read more
was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.
Read less
Was this helpful?
Thank you for voting!
The dryer would run i.e. the drum would turn, but there was no heat so the clothes didn’t dry.
33 of 38 people
found this instruction helpful.
-
David from Joppa, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both
... Read more
parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.
Read less
Was this helpful?
Thank you for voting!
Drum stopped turning, fan continued to blow
31 of 34 people
found this instruction helpful.
-
Richard from Davie, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, e
... Read more
tc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.
Read less
Was this helpful?
Thank you for voting!
Dryer would start and heat, but after 1st cycle the burner would not fire and a buzzing sound was coming from the gas valve solenoid area. Igniter and other functions worked fine.
32 of 38 people
found this instruction helpful.
-
David from Bedford, IN
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Removed front of dryer, unplugged each coil to determine where buzzing was coming from.....determined it was the boosting coil....ordered part and replaced. Dryer works great....we think it had be going bad over time because drying times have noticeable decreased.
Was this helpful?
Thank you for voting!
Dryer had heat intermittently and would take 3 cycles to dry a load of clothes
35 of 48 people
found this instruction helpful.
-
ANTHONY from MONROE, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver
First, remove the back panel of dryer which is about 10 screws. Then remove the 2 thermal switches, one is above the heating element and the other is where the hot air comes out. They are both really easy to get to and the pictures on Part Select.com are identical, so you can order the part first and then just "match them up" if you are
... Read more
not sure what to replace. Oops, the first step is to unplug the dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer belt snapped
33 of 42 people
found this instruction helpful.
-
J. from Oakdale, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the ... Read more dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the ... Read more dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.
Read less
Was this helpful?
Thank you for voting!
dryer would not continuously heat, and took several cycles to dry clothes. The flame would ignite and heat the dryer at first, but then would ignite and go out quickly for the rest of the cycle. I tried the thermostats first with no luck.
31 of 36 people
found this instruction helpful.
-
Ryan from Livonia, MI
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wir
... Read more
es connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.
Read less
Was this helpful?
Thank you for voting!
dryer would not heat
31 of 37 people
found this instruction helpful.
-
Leon from Jasper, AL
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the four screws holding the
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people
found this instruction helpful.
-
Bill from Houston, TX
- Really Easy
- Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
push to start switch was not working
33 of 43 people
found this instruction helpful.
-
Grace from New Smyrna Beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this helpful?
Thank you for voting!
The Dryer had no heat
30 of 34 people
found this instruction helpful.
-
Michael from Plano, TX
- Easy
- 15 - 30 mins
-
Socket set
I ordered up a new heating coil. It was plug and play, real easy to do. Make sure to turn on the dryer with the before you put it back together to make sure the heating coils heat up. Be careful though, it will get real hot, so run for a second or two. Also, you may see a little smoke as the coil burns in, that should be fine. Once i
... Read more
t is tested and works, let it cool off, then reattach it, put on the backplate and you are done!
Read less
Was this helpful?
Thank you for voting!
dryer wouldn't dry at all
33 of 44 people
found this instruction helpful.
-
David from Bend, OR
- Easy
- 15 - 30 mins
-
Nutdriver
1. UNPLUG 2.Undo 8 screws @ back of dryer. Locate heating element midway down on right about 6"x10" has three thermostat wires connected to it undo the 2 screws & 3 wires either order. You will need to pry up GENTLY on the thermostat on the old element. Replace themostat to new element and make a test run to make sure its running and H
... Read more
OTand repeat steps in reverse order...
Read less
Was this helpful?
Thank you for voting!
My dryer only heats up at the beginning of cycle so my clothes will not dry.
31 of 39 people
found this instruction helpful.
-
Monique from Mission Viejo, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this helpful?
Thank you for voting!
No dryer heat
29 of 33 people
found this instruction helpful.
-
lori from windsor, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Took the back off with a cordless drill with an apex holder. I unplugged the old wires from the old heating element and plugged them into the new heating element. Put the back back on after testing it to make sure it worked and that was it. Since this element was in a housing it was really simple to reinstall the new one.
Was this helpful?
Thank you for voting!