110694 Kenmore Dryer - Instructions

All Instructions for the 110694
46 - 60 of 2277

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would get hot for a while, then quit heating
56 of 70 people found this instruction helpful.
  • Sharon from Houston, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
After reading about other people with this same problem I took a chance that this would be what was wrong with my dryer.I took off the front cover of the dryer by removing two screws. I located the faulty coils and simply plugged in the 2 new coils Tah-dah Probably coud have been done without even removing the front panel, but since it was off I vacuumed out the lint ( actually my husband did all of the above, but I tell a better tale than he does and I diagnosed the problem and ordered theparts)
Was this helpful?
Thank you for voting!
the dryer only blew cold air
48 of 52 people found this instruction helpful.
  • charles from waukesha, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
Was this helpful?
Thank you for voting!
Dryer motor would not turn on
51 of 69 people found this instruction helpful.
  • John from Bluffton, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
Was this helpful?
Thank you for voting!
One of the power cord connections on the terminal block was loose. Screw on terminal block was cross threaded when installed. Took six years to smoke the wire.
52 of 72 people found this instruction helpful.
  • DAVID from LEESBURG, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set, Wrench set
Removed and replaced terminal block, power cord and black wire to timer.
Was this helpful?
Thank you for voting!
door switch - broken tab
44 of 50 people found this instruction helpful.
  • Nick from Reynoldsburg, OH
  • Easy
  • Less than 15 mins
  • Screw drivers
Unplugged dryer, removed two screws from the lint trap area, pried up the top of the dryer to get to the switch, removed two screws securing the switch, unplugged the switch, plugged in the new one and reversed the procedure.
Was this helpful?
Thank you for voting!
Dryer would not start
42 of 46 people found this instruction helpful.
  • DAVID from WAREHAM, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My wife was doing a load of laundry when she thought the the dry cycle was finished she found the cloths still wet. When she went to restart the dryer nothing. I did some research online and found the most common problem was the thermal fuse. I removed the back of the dryer removed the fuse and checked for continuity with my volt meter . I thought that I was going to find alot of lint build up. However I did not so I decieded to also replace the thermostat, using the thermo cut-off kit because this might have caused the fuse to fail. I ordered the parts from partselect and they arrived in two days. Partselect has excellent instructional videos on how to make the repair. It was quick and easy and saved the money of just going out and buying a new appliance.
Was this helpful?
Thank you for voting!
No power
45 of 55 people found this instruction helpful.
  • Nick from Brandon, FL
  • Easy
  • 1- 2 hours
  • Nutdriver
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.
Was this helpful?
Thank you for voting!
Intermittent or no gas ignition, HSI ignightor working
43 of 50 people found this instruction helpful.
  • Steven from Sauk Village, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed front of gas dryer and cleaned all lint out. Checked HSI, and cleaned flame sensor. Split (3 terminal) gas coil terminals were intermittent. Read about 700 ohms across outer two terminals, but center terminal to either outer terminal was open (Infiniti on meter) 2 terminal coil measured about 550 ohms. 3 terminal coil should read about 700 ohms across outer terminals, and about 1.5K ohms center to outer terminals. Unscrewed index cover plate and replaced coil, 2 terminal coil was okay. Reassembled and finished 12 loads of laundry no problems at all.
Was this helpful?
Thank you for voting!
Busted Belt & Pulley
43 of 51 people found this instruction helpful.
  • James from West Haven, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I bought a belt from a store in my area- What a mistake...I found this site and read all the stories on how easy it was and how PartSelect.com had the parts in stock and had easy instructions...I put the idler pulley in place, put the belt in place (all from instructions included) and put the dryer back together (which was easy). I actua lly did it alone. I would recommend this company to anyone in need of their parts and help!
Was this helpful?
Thank you for voting!
Dryer would not shut off on auto dry settings
42 of 50 people found this instruction helpful.
  • Wiliam from Belleville, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.
Was this helpful?
Thank you for voting!
the dryer element was not coming on and looked like it had burned up
41 of 51 people found this instruction helpful.
  • Benjamin from Greenville, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
i decided to order the new element which was the most expensive part then decided to add the thermostats just incase they were bad because they were rather inexpensive. got the parts in took the back off the dryer located the parts i ordered and simply replaced them with the power cut off to the unit. put the back on and it heated like i t was better that new my clothes dry 5 times faster than it did when i bought the thing.
Was this helpful?
Thank you for voting!
dryer makes a lot of noice, bad rolleres
37 of 40 people found this instruction helpful.
  • Jesus E from Palm Bay, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.
Was this helpful?
Thank you for voting!
Gas burner would not ignite
37 of 42 people found this instruction helpful.
  • Jack from Conroe, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
(I knew the gas coils were bad, since the gas ignitor would glow brightly as the burner attempted to ignite. So I knew everything except the gas valve was operating normally.)

Unplug the electrical cord to the dryer. Remove the front access panel. Remove the retainer clip for the gas coils (2 screws). Remove the coils and unpl ug the electrical connections. Connect the new coils to their respective electricl connections. Slide the nes coils back onto their respective posts on the gas valve. Replace the retainer clip, and 2 screws to hold it in place. (I then plugged the dryer back into the wall outlet to visually check the burner operation) Everything worked fine so I then replaced the front panel.
Was this helpful?
Thank you for voting!
dryer drum wouldn't turn
36 of 40 people found this instruction helpful.
  • Steve from Peachtree City, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure ou t you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!
Was this helpful?
Thank you for voting!
replaced heating element in my dryer
38 of 51 people found this instruction helpful.
  • Marlene from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Socket set
I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)
Was this helpful?
Thank you for voting!
All Instructions for the 110694
46 - 60 of 2277