1106909 Kenmore Washer Dryer Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The switch in the door of the dryer was broken so it would keep running when you opened the door
0 of 1 people
found this instruction helpful.
-
Matt from Stilwell, KS
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a
... Read more
simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.
Read less
Was this helpful?
Thank you for voting!
latch not working on Kenmore dryer
0 of 1 people
found this instruction helpful.
-
sally from Houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Was this helpful?
Thank you for voting!
Dryer door wouldn't stay latched shut during cycle
0 of 1 people
found this instruction helpful.
-
KRISTIN from DENVER, CO
- Really Easy
- Less than 15 mins
-
Pliers
In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!
Was this helpful?
Thank you for voting!
Dryer stopped working
0 of 1 people
found this instruction helpful.
-
Mike from Conway, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th
... Read more
e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.
Advice: Don't slam the dryer door. The actuator will last longer.
Advice: Don't slam the dryer door. The actuator will last longer.
Read less
Was this helpful?
Thank you for voting!
Door would not latch closed when shut
0 of 1 people
found this instruction helpful.
-
Carl from Port Arthur, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.
Was this helpful?
Thank you for voting!
door wouldn"t close tightly
0 of 1 people
found this instruction helpful.
-
Noreen from Fairfax, VA
- Easy
- Less than 15 mins
-
Screw drivers
removed the broken part and replaced with the new one
Was this helpful?
Thank you for voting!
Dryer door would not close
0 of 1 people
found this instruction helpful.
-
Felipe from Helotes, TX
- Really Easy
- Less than 15 mins
Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!
Was this helpful?
Thank you for voting!
the dryer would not turn on
0 of 1 people
found this instruction helpful.
-
James from Shortsville, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab
... Read more
out 10 minutes.
Read less
Was this helpful?
Thank you for voting!
Dryer would not turn on, found metal clip in laundry
0 of 1 people
found this instruction helpful.
-
Terry from Carlsbad, CA
- Easy
- Less than 15 mins
-
Screw drivers
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.
*** Unplug machine ****
To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ... Read more ss fit in place and will pry open with a flat screwdriver).
Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!
Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
*** Unplug machine ****
To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ... Read more ss fit in place and will pry open with a flat screwdriver).
Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!
Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
Read less
Was this helpful?
Thank you for voting!
the door catch was broken and I was using duct tape to close the dryer!!
0 of 1 people
found this instruction helpful.
-
margery from Lake Spivey, GA
- Really Easy
- Less than 15 mins
-
Pliers
This was a classic easy repair and I am sure saved us bundles on a service call.
Was this helpful?
Thank you for voting!
replace the latch
0 of 1 people
found this instruction helpful.
-
Dennis from Perkasie, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
take the old latch out and pop the new one in. Your repair kit worked perfect.
Was this helpful?
Thank you for voting!
Wife pulled bed sheets out of drier and broke door switch actuator
0 of 1 people
found this instruction helpful.
-
Ernest from Moundsville, WV
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.
Was this helpful?
Thank you for voting!
Dryer would not come on
0 of 1 people
found this instruction helpful.
-
Steven from Bassett, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this helpful?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
0 of 1 people
found this instruction helpful.
-
Larry from Elmhurst, IL
- Easy
- 30 - 60 mins
-
Screw drivers
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this helpful?
Thank you for voting!
Broken dryer door latch.
0 of 2 people
found this instruction helpful.
-
Fred from Encino, CA
- Really Easy
- Less than 15 mins
Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would hav
... Read more
e been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.
Read less
Was this helpful?
Thank you for voting!