- Home
- 1106807913
- Instructions
1106807913 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer quit spinning but was still heating so figured belt........
2 of 2 people
found this instruction helpful.
-
Shannin from ROCKPORT, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. P
... Read more
ut new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......
Read less
Was this helpful?
Thank you for voting!
The belt needed replaced
3 of 5 people
found this instruction helpful.
-
Judith from Guys Mills, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.
Was this helpful?
Thank you for voting!
belt broke
2 of 2 people
found this instruction helpful.
-
Helen from WEST MONROE, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
watched your video on 'how to' and did it like man showed..no problem
Was this helpful?
Thank you for voting!
Dryer stopped working.
3 of 5 people
found this instruction helpful.
-
Andrew from Edina, MN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.
Other Parts Used:
Was this helpful?
Thank you for voting!
Bad Motor, Would not start.
3 of 5 people
found this instruction helpful.
-
Steve from S LAKE TAHOE, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very
... Read more
tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Read less
Was this helpful?
Thank you for voting!
Wish it would have told us that when the front was removed the dryer drum falls.
2 of 2 people
found this instruction helpful.
-
Judy from MONTPELIER, OH
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.
Was this helpful?
Thank you for voting!
The original motor stopped working
2 of 2 people
found this instruction helpful.
-
Robert from PFLUGERVILLE, TX
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexib
... Read more
le dryer tube since the old one had a few holes. It works perfectly again.
Read less
Was this helpful?
Thank you for voting!
Replacing the dryer drum drive belt
2 of 2 people
found this instruction helpful.
-
walt from LK HAVASU CTY, AZ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time)
... Read more
and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.
Read less
Was this helpful?
Thank you for voting!
Loud banging coming from drum area.
2 of 2 people
found this instruction helpful.
-
Larry from S ROCKWOOD, MI
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got
... Read more
the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum roller bearing was out and making a banging noise
2 of 3 people
found this instruction helpful.
-
William from La Porte, IN
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
removed the top of the dryer exposing the drum and belt.Also the bottom acess door was removed.The rollers were easy to get to from the bottom and from the back.Had to remove ducting from the rear of the dryer to expose the upper most roller shaft nut.Loosened the nuts from the back making the wheels come from the bottom.Also had to loose
... Read more
n the support bracket holding the weight up on the bottom roller assy.Replaced the belt by rapping it around the drum before installing the roller wheels.This project was easy except trying to hold the upper shaft in place while putting the nut back on the shaft.This would be much easier with a second person.Thanks for making this a nice experience and easy fix !
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud noise while in use
2 of 3 people
found this instruction helpful.
-
Josh from Madill, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people
found this instruction helpful.
-
Laszlo from Vienna, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people
found this instruction helpful.
-
katherine from Salem, OR
- Easy
- 15 - 30 mins
-
Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw
... Read more
s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Read less
Was this helpful?
Thank you for voting!
Blower (fan) assembly and old model motor with different electrical connections
2 of 3 people
found this instruction helpful.
-
Dana from RESTON, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly
Recommend 10" or larger 14" will definitely do the job
2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatu ... Read more ral
3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Recommend 10" or larger 14" will definitely do the job
2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatu ... Read more ral
3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Fan blade had to be removed , was broken off from motor.
2 of 3 people
found this instruction helpful.
-
James from Colorado Springs, CO
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
Was this helpful?
Thank you for voting!