- Home
- 1106807913
- Instructions
1106807913 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Mother was frozen up
3 of 3 people
found this instruction helpful.
-
Dan from SYRACUSE, UT
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people
found this instruction helpful.
-
David from JOLIET, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
broken blower wheel
3 of 3 people
found this instruction helpful.
-
Vern from NEWBERG, OR
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
Was this helpful?
Thank you for voting!
the dryer would not turn on
4 of 6 people
found this instruction helpful.
-
Warren from PHILADELPHIA, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off t
... Read more
he front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer Drum Belt Broken
3 of 3 people
found this instruction helpful.
-
george s from las vegas, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made m
... Read more
ore in change than the belt cost!
Overall an easy repair. Belt came with diagram for easy threading the belt.
Overall an easy repair. Belt came with diagram for easy threading the belt.
Read less
Was this helpful?
Thank you for voting!
Let the kids do it.
3 of 3 people
found this instruction helpful.
-
Robert from Rocky Mount, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.
I gav ... Read more e my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.
She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.
When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis
OK, so much for the intro.
I gav ... Read more e my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.
She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.
When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis
Read less
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people
found this instruction helpful.
-
Craig from VASS, NC
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken belt
3 of 4 people
found this instruction helpful.
-
peter from portland, OR
- Easy
- 15 - 30 mins
-
Nutdriver
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt fro
... Read more
m potentially slipping off the driveshaft.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people
found this instruction helpful.
-
Wayne from Rosenberg, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate
... Read more
d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Read less
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people
found this instruction helpful.
-
Ed from Charlottesville, VA
- Easy
- Less than 15 mins
-
Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen
... Read more
t, and other parts. At some point it will be time for a new dryer...
Read less
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people
found this instruction helpful.
-
Mark from Clarksburg, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R
... Read more
einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Read less
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people
found this instruction helpful.
-
Russell from Apache Junction, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u
... Read more
p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Read less
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people
found this instruction helpful.
-
WILFRED from NORTH HIGHLANDS, CA
- Really Easy
- Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Dryer making a screeching noise. Diagnosed by removing idler pulley first, then turning the motor and learning that it was the motor that was squeaking or the blower fan.
3 of 4 people
found this instruction helpful.
-
Linda from GIBSONIA, PA
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Ordered the motor with pulley and blower wheel in case the wheel did not come free from the motor.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blow ... Read more er wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.
Took out the lint screen, took off the top and disconnected the wires for the door switch, took off the front.
Remove the idler poi and the belt and then removed the drum.
I read in other repair YouTube videos, the blow ... Read more er wheel sometimes is so seized onto the motor axle that you have to remove the wheel by cutting it off.
Yes, ours seized!
Cut off the motor axle with a hacksaw and then the motor and the wheel were free. This was not an issue since I had purchased both the motor and the wheel which I recommend doing anyway. Our dryer over 25 years old and it does not have many electrical components, which I love. We removed the parts put in the new parts. Follow the wiring diagram to get the new motor hooked up.
Then I replaced the drum support rollers, which were a snap and then we put it all back together.
We added an extra step because we had to takeoff the back of the dryer to gain access to the blower. It turned out to be a good thing since years of lint have been trapped at the bottom of the lint chute.
I cleaned everything, washed everything and put it all back together and it purrs like a kitten.
Took us about 2 1/2 hours total since we are very cautious and slow as we didn’t want to break things.
I am very happy with the end result and hopefully it will last another 25 years!
Parts were spot on and worked perfectly.
Much more economical than buying a new dryer for $750-$1000.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!