1106518721 Kenmore Dryer - Instructions

All Instructions for the 1106518721
121 - 135 of 343

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
door latch broke
1 person found this instruction helpful.
  • Debra from Oakland, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pop out the old latch and replaced with a new one
Was this helpful?
Thank you for voting!
door catch broke therefore dryer door would not close
1 person found this instruction helpful.
  • vernette from sprague, WA
  • Really Easy
  • Less than 15 mins
just put the new part in the door---sooo easy! THANK YOU!
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person found this instruction helpful.
  • j from TAZEWELL, TN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person found this instruction helpful.
  • Tammy from glenford, OH
  • Very Easy
  • Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Susan from HUDSON, MA
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Dryer drum wasn't turning
1 person found this instruction helpful.
  • Carrie from PLAINFIELD, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person found this instruction helpful.
  • Mark from TERREBONNE, OR
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Frank from ENDICOTT, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person found this instruction helpful.
  • Barbara from NORTH EASTON, MA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person found this instruction helpful.
  • Kenneth from UPPR MARLBORO, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
latch was broke
1 person found this instruction helpful.
  • Rick from SAN DIEGO, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
Handle on lint filter cracked and came apart
1 person found this instruction helpful.
  • ROSEMARIE*SALVO from BRONX, NY
  • Very Easy
  • Less than 15 mins
Opebed lint filter door, removed old lint filter and replaced it with new one.
Was this helpful?
Thank you for voting!
Old filter handle broke
1 person found this instruction helpful.
  • ronald from PICKENS, WV
  • Really Easy
  • Less than 15 mins
replaced filter
Was this helpful?
Thank you for voting!
filter had holes
1 person found this instruction helpful.
  • Sheila from MOUNT VERNON, IL
  • Very Easy
  • Less than 15 mins
pulled old filter out and then slid the new filter in Done
Was this helpful?
Thank you for voting!
door would stay closed
1 person found this instruction helpful.
  • william from KILLEEN, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
All Instructions for the 1106518721
121 - 135 of 343