- Home
- 1106518721
- Instructions
1106518721 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer making excessive noise; then continued to blow circuit
1 person
found this instruction helpful.
-
Ava from BALTIMORE, MD
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit
... Read more
-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Read less
Was this helpful?
Thank you for voting!
rollers had been new too long!
1 person
found this instruction helpful.
-
Scott from EVEREST, KS
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this helpful?
Thank you for voting!
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
broken belt
1 person
found this instruction helpful.
-
William from Newport, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in busine
... Read more
ss
Read less
Was this helpful?
Thank you for voting!
Loud hum but wouldn't work with a load in
2 of 4 people
found this instruction helpful.
-
Ronald from Tulsa, OK
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.
Was this helpful?
Thank you for voting!
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
1 person
found this instruction helpful.
-
Mark from BLOOMFIELD, CT
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this helpful?
Thank you for voting!
dryer door won't stay shut
2 of 4 people
found this instruction helpful.
-
Diana from Canfield, OH
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth ever
... Read more
y penny to fix correctly instead of rigging it. Do it!
Read less
Was this helpful?
Thank you for voting!
catch was missing to close dryer door
2 of 4 people
found this instruction helpful.
-
DONNA from SAN LORENZO, CA
- Really Easy
- Less than 15 mins
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person
found this instruction helpful.
-
Victor from NORFOLK, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
The door whould not close enough for the dryer to work.
1 person
found this instruction helpful.
-
Frank from Union Beach, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this helpful?
Thank you for voting!
dryer wouldn't turn on
1 person
found this instruction helpful.
-
Kim from Northridge, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions
... Read more
on your website!! Simple as could be!
Read less
Was this helpful?
Thank you for voting!
Broken door switch
2 of 4 people
found this instruction helpful.
-
john from el paso, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and
... Read more
pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Read less
Was this helpful?
Thank you for voting!
dryer door wouldn't catch, catch was broken
1 person
found this instruction helpful.
-
Theodore from Tyler, TX
- Really Easy
- Less than 15 mins
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this helpful?
Thank you for voting!
broken door catch
2 of 4 people
found this instruction helpful.
-
Michael from Goddard, KS
- Really Easy
- Less than 15 mins
the part fit perfectly, it just snaped right into place.
Was this helpful?
Thank you for voting!
Dryer door would not stay closed
1 person
found this instruction helpful.
-
Gregg from St. Augustine, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this helpful?
Thank you for voting!