1106510 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bought motor, then bought blower wheel also
95 of 111 people
found this instruction helpful.
-
Daniel from Coatesville, PA
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Wrench (Adjustable)
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw!
... Read more
Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
Read less
Was this helpful?
Thank you for voting!
Dryer lost heat but kept spinning
95 of 129 people
found this instruction helpful.
-
Dave from Boise, ID
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed rear panel 10 screws, and heating element was situated on the right hand side of dryer and was held in place by two screws and had two heavy duty red wires connected to the element which were easily removed . Installing this item was a breeze .
Was this helpful?
Thank you for voting!
Door won't latch
95 of 158 people
found this instruction helpful.
-
Jill from bellevue, WA
- Really Easy
- Less than 15 mins
-
Pliers
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks
Was this helpful?
Thank you for voting!
Replacing worn drum support rollers and shafts.
60 of 69 people
found this instruction helpful.
-
Gary from Canton, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Very easy once I figured out how to open it up to see what was the matter.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the ... Read more front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.
Good luck, It s not as bad as it sounds.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the ... Read more front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.
Good luck, It s not as bad as it sounds.
Read less
Was this helpful?
Thank you for voting!
Rear Dryer Seal was old and staining clothing
58 of 65 people
found this instruction helpful.
-
Grace from Phoenix, AZ
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
After unplugging the dryer,I removed 2 bolts on the back top of the dryer, then removed the two screws in the lint box area. I used a screw driver to help force the top panel of the dryer up. When open, I removed the top screws that held the front and side panels together. I then lifted the front panel up and away from the dryer, so there
... Read more
would be room to take the drum out. I removed the belt from the pulley (located under the drum) and slid the drum out. I removed the old seal, cleaned up the drum and the inside of the dryer, then glued the new seal on. After the glue was dry, I put the drum back in (with the belt on the drum), put the belt back on the pulley and proceeded to put the dryer front back on. Once the front was on, I put the top back on and replaced the bolts on the back of the dryer. I plugged it in and it is working great! By the way, before this, I had NEVER attempted to repair a dryer before and I am female. If I could do it, so can anyone else willing to try :)
Read less
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people
found this instruction helpful.
-
RONALD from SALMON, ID
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!
Dryer would not shut off on auto dry settings
42 of 50 people
found this instruction helpful.
-
Wiliam from Belleville, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.
Was this helpful?
Thank you for voting!
the dryer element was not coming on and looked like it had burned up
41 of 51 people
found this instruction helpful.
-
Benjamin from Greenville, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver
i decided to order the new element which was the most expensive part then decided to add the thermostats just incase they were bad because they were rather inexpensive. got the parts in took the back off the dryer located the parts i ordered and simply replaced them with the power cut off to the unit. put the back on and it heated like i
... Read more
t was better that new my clothes dry 5 times faster than it did when i bought the thing.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer sounded like it had rocks in it when running
34 of 38 people
found this instruction helpful.
-
Mark from Kirkwood, MO
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Following the instructions that came with the parts, I removed the top off of the dryer, which was very easy, two more 5/16" screws and I had the drum out. I confess, this was my second time at this repair. 1st time I neglected to replace the rear drum seal which I strongly recommend you do while you have it open. I only replaced the 2 w
... Read more
heels last time and it failed very soon afterwards.
Lesson Learned: Always replace the rear drum seal when you replace the support wheels!!!
Lesson Learned: Always replace the rear drum seal when you replace the support wheels!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
replaced heating element in my dryer
38 of 51 people
found this instruction helpful.
-
Marlene from Indianapolis, IN
- Really Easy
- Less than 15 mins
-
Socket set
I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)
Was this helpful?
Thank you for voting!
The dryer would run i.e. the drum would turn, but there was no heat so the clothes didn’t dry.
33 of 38 people
found this instruction helpful.
-
David from Joppa, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both
... Read more
parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.
Read less
Was this helpful?
Thank you for voting!
Dryer had heat intermittently and would take 3 cycles to dry a load of clothes
35 of 48 people
found this instruction helpful.
-
ANTHONY from MONROE, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver
First, remove the back panel of dryer which is about 10 screws. Then remove the 2 thermal switches, one is above the heating element and the other is where the hot air comes out. They are both really easy to get to and the pictures on Part Select.com are identical, so you can order the part first and then just "match them up" if you are
... Read more
not sure what to replace. Oops, the first step is to unplug the dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Dryer had no heat
30 of 34 people
found this instruction helpful.
-
Michael from Plano, TX
- Easy
- 15 - 30 mins
-
Socket set
I ordered up a new heating coil. It was plug and play, real easy to do. Make sure to turn on the dryer with the before you put it back together to make sure the heating coils heat up. Be careful though, it will get real hot, so run for a second or two. Also, you may see a little smoke as the coil burns in, that should be fine. Once i
... Read more
t is tested and works, let it cool off, then reattach it, put on the backplate and you are done!
Read less
Was this helpful?
Thank you for voting!
dryer would not heat
31 of 37 people
found this instruction helpful.
-
Leon from Jasper, AL
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the four screws holding the
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people
found this instruction helpful.
-
Bill from Houston, TX
- Really Easy
- Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!