1106404 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Machine would not start and light stayed on with door closed.
1 person
found this instruction helpful.
-
Mark from TERREBONNE, OR
- Very Easy
- Less than 15 mins
-
Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo
... Read more
w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Read less
Was this helpful?
Thank you for voting!
Broken door switch
2 of 4 people
found this instruction helpful.
-
john from el paso, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and
... Read more
pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Read less
Was this helpful?
Thank you for voting!
dryer latch engagem ent
1 of 2 people
found this instruction helpful.
-
Earl from Terre Haute, IN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
our son was able to diagnosis and order the part and very pleased with quite response. Dryer now working fine.
Was this helpful?
Thank you for voting!
my stovetop light did not work
1 of 2 people
found this instruction helpful.
-
Geraldine M. from Fork Union, VA
- Really Easy
- 15 - 30 mins
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No applianc
... Read more
e store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Read less
Was this helpful?
Thank you for voting!
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
2 of 5 people
found this instruction helpful.
-
Patrick from Ramsey, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on a
... Read more
nd reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
Read less
Was this helpful?
Thank you for voting!
old tube burned out
2 of 5 people
found this instruction helpful.
-
JERRY from SPANISH FORK, UT
- Really Easy
- Less than 15 mins
removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.
Was this helpful?
Thank you for voting!
Door latch snapped off.
1 of 2 people
found this instruction helpful.
-
Karen from Randle, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.
Was this helpful?
Thank you for voting!
Broken door actuator spring -interposer for motor control
1 of 2 people
found this instruction helpful.
-
Stephen from Vancouver, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people
found this instruction helpful.
-
Rick from BETHESDA, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people
found this instruction helpful.
-
Daniel from TRENTON, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said.
... Read more
I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Read less
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people
found this instruction helpful.
-
Edward from Nanuet, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people
found this instruction helpful.
-
Andris from Sands Point, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Read less
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people
found this instruction helpful.
-
linda from las cruces, NM
- Easy
- 15 - 30 mins
-
Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people
found this instruction helpful.
-
peggy ann from forest city, NC
- Really Easy
- Less than 15 mins
very easy
Was this helpful?
Thank you for voting!