1106404 Kenmore Washer - Instructions

All Instructions for the 1106404
91 - 103 of 103

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
door would not activate dryer......lever broke!
  • nancy from troy, MT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!
Was this helpful?
Thank you for voting!
Dryer won't start
  • Michael from Cincinnati, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers
Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.
Was this helpful?
Thank you for voting!
actuator spring lever broke
  • george from port angeles, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clo thes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened
Was this helpful?
Thank you for voting!
Missing lid hinge bearing
  • Kim from Oviedo, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid an d into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this helpful?
Thank you for voting!
Light bulb failure
  • Grant from Alexandria, VA
  • Really Easy
  • Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Washer Had A Continuous Moan And Vibration
  • Roger from Millis, MA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Wrench set
I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred th e bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.
Was this helpful?
Thank you for voting!
Switch broken
  • Willie from Virginia Beach, VA
  • Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the lo cation and design of the switch. I got it though.
Was this helpful?
Thank you for voting!
Washer quit running when lid was closed
  • Colleen from Indianapolis, IN
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.
Was this helpful?
Thank you for voting!
Had issues with removing the inner tub
  • Bruce from Yankton, SD
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
Was this helpful?
Thank you for voting!
dryer wouldn't start
  • sean from easthampton, MA
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers
I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. al most spent $400.00 on a new one.
Was this helpful?
Thank you for voting!
over fill water
  • ronnie from meriden, CT
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
replace the water valve
Was this helpful?
Thank you for voting!
broken
  • Tomas from Orlando, FL, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Removed the old one installed the new one
Was this helpful?
Thank you for voting!
Washer leaking
  • Forrest from Oxford, AL
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Was this helpful?
Thank you for voting!
All Instructions for the 1106404
91 - 103 of 103