1106301 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Dryer stopped working completely.
13 of 18 people
found this instruction helpful.
-
Elyse from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.
Was this helpful?
Thank you for voting!
squeaking sound due to worn out bearing idler pulley wheel.
13 of 18 people
found this instruction helpful.
-
Evan from NORTHRIDGE, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut scr
... Read more
ews of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.
Read less
Was this helpful?
Thank you for voting!
Dryer timer stopped working
13 of 18 people
found this instruction helpful.
-
James from Park City, UT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Unfortunately it is not easy to get to this part due to the fact the control panel is attached to the top of the dryer by both plastic clips and screws. I was able to bend the back down in the back to gain access to the two screws that held the dryer timer in place. This job is much easier if you have an assistant to hold the thin tin o
... Read more
r steel backing away from the control panel while reconnecting the wire sensors to the new timer. This is the second time I have used Parts Select they are excellent and their prices are very competitive. The part was identical to the broken part. I saved at least $100 by doing the job myself.
Read less
Was this helpful?
Thank you for voting!
Dryer would not generate heat
11 of 13 people
found this instruction helpful.
-
Douglas from Greensburg, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
My dad was ready to spend $2000 on a new washer/dryer (he has to have a matching set!). Anyway, his dryer would not generate heat. A google search turned up partselect.com, which walked me through the procedure to see what we needed.
It turned out to be a simple to replace $25.00 part! The dryer is drying as if it was brand ... Read more new. Saved $1,975. Hehe.
Thanks, partselect!
It turned out to be a simple to replace $25.00 part! The dryer is drying as if it was brand ... Read more new. Saved $1,975. Hehe.
Thanks, partselect!
Read less
Was this helpful?
Thank you for voting!
dryer would not turn off when the door is open
10 of 10 people
found this instruction helpful.
-
James from Webster, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
it took loess than 10 minutes to change the door switch after watching the repair video
Was this helpful?
Thank you for voting!
Dryer Would Not Start.
11 of 13 people
found this instruction helpful.
-
GALEN from NEDERLAND, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy a
... Read more
s the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.
Read less
Was this helpful?
Thank you for voting!
my dryer would not heat up any longer
10 of 11 people
found this instruction helpful.
-
Chris from Great Bend, KS
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screw
... Read more
s back in and fastend the front back on and were in bussiness!
Read less
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people
found this instruction helpful.
-
Eric from West Chester, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people
found this instruction helpful.
-
Peter from HUEYTOWN, AL
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Door switch was broken
11 of 14 people
found this instruction helpful.
-
Anthony from Orlando, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro ... Read more m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro ... Read more m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
Read less
Was this helpful?
Thank you for voting!
Broken belt. Broken idle pully and replace 4 rollers
11 of 14 people
found this instruction helpful.
-
Mike from INOLA, OK
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
Was this helpful?
Thank you for voting!
would not stop when opening door during cycle
10 of 11 people
found this instruction helpful.
-
PHILIP from MATTHEWS, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to
... Read more
take the time to remove dust and lint from behind the dryer. Easy repair.
Read less
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people
found this instruction helpful.
-
stephen from langley, KY
- Really Easy
- Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people
found this instruction helpful.
-
Dawn from Chesapeake City, MD
- Really Easy
- Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people
found this instruction helpful.
-
Michael from ENOLA, PA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Other Parts Used:
Was this helpful?
Thank you for voting!