1106301 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Timer would not move, leaving dryer running
14 of 16 people
found this instruction helpful.
-
John from Lockport, NY
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed screws from back panel. Removed two scews from timer. Disconnected one wire at a time and transfered to new timer until all wires were transfered. Reattached new timer and reattached back panel.
Was this helpful?
Thank you for voting!
Thermal fuse was bad.
16 of 22 people
found this instruction helpful.
-
Brad from Odessa, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.
Thanks for the help.
Thanks for the help.
Was this helpful?
Thank you for voting!
Dryer would leave clothes damp
15 of 20 people
found this instruction helpful.
-
Luke from Elmira, NY
- Easy
- Less than 15 mins
-
Nutdriver
First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling the
... Read more
rmostat in place. It was pretty easy.
Read less
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people
found this instruction helpful.
-
Richard from Duarte, CA
- Really Easy
- Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people
found this instruction helpful.
-
Richard from SAUGERTIES, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
the dryer was making squealing noises when it first started.
13 of 15 people
found this instruction helpful.
-
Christine from BIRCH RUN, MI
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Was this helpful?
Thank you for voting!
The dryer suddenly started running cold - it would turn, the timer worked...but no heat. My wife mentioned that it had been taking longer and longer to dry a load of clothes....
12 of 12 people
found this instruction helpful.
-
Geoff from Farmington, CT
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Popped the lower cover off the dryer, found the thermal fuse and thermostat mounted on the heating tube. Removed the screws with a nutdriver, swapped wires to the new parts, and reinstalled. Then I spent 30 minutes vacuuming 13 years worth of lint and crud out of the machine - it was pretty gummed up in spots, which is probably the cause
... Read more
of the failure.
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
Read less
Was this helpful?
Thank you for voting!
Defective Door Switch
12 of 13 people
found this instruction helpful.
-
George from Bedford, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I a
... Read more
m 80 years old). Your video is great. Gives step by step instructions.
Read less
Was this helpful?
Thank you for voting!
Dryer door switch
12 of 13 people
found this instruction helpful.
-
Frank from STANFORDVILLE, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
We watched the video on ur website! Thank you
Was this helpful?
Thank you for voting!
Dry was making a loud squeaking noise.
12 of 13 people
found this instruction helpful.
-
Michael from OREGON CITY, OR
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people
found this instruction helpful.
-
JEANMARIE from BELLEROSE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people
found this instruction helpful.
-
William from Pontiac, MO
- Easy
- More than 2 hours
-
Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Dryer produced no heat. My lint trap was full of wet lint.
11 of 12 people
found this instruction helpful.
-
William from LAUREL, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant a ... Read more mount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant a ... Read more mount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!