11062182103 Kenmore Dryer - Instructions

Went on line and determined the problem was the thermal fuse. Removed the rear panel of the dryer, removed the leads from the thermal fuse, hooked them together and started the dryer. That confirmed the problemwas the existing fuse.Ordered the new thermal fuse, installed the fuse, hooked up the wires and it works finel Very simple fix. About a 10 year old dryer.

I ordered this to repair my girlfriend's mother's dryer. But according to my luck, the day the part was to arrive, I suffered an small brain bleed that put me in the hospital for a couple of weeks. I had read the instructions and was able to explain it to my girlfriend who replaced it and got it all back going right!

Before anything unplug the dryer
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.

Took the dryer apart and replaced the idler pulley with bracket and the drive belt

Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..

removed the rear panel to gain access to the internals of the dryer, removed the one screw that retains the fuse, out with the old and in with the new.
delivery of the part was 2 days sooner than expected.
could not have been a simpler process!

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

Once again part select has come through for me. googled dryer won't start and a video on utube came up. typed my model number in on part select website and followed directions. was easy got part in three business days regular shipping. very pleased with this site.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Disconnect gas line and vent hose,removed top and back covers to install belt.

I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

I guess you could say I went through the process of elemanation, first I replased the thermostat,removed 2 screws pulled off 3 wired with a pair of pliers put them on the new one, still no hot air so I replaced the fuse, took out 1 screw removed 2 wires and placed them on the new fuse, still no hot air, finally I replaced the thermal cut-off switch and WOW that was it hot air was blowing again, the process was very easy I ordered everything from parts slect and they were here the next day, only had to take the back off the dryer with a nut wrench, locate the thernastat, fuse and thermal cut-off which was just above the heating coil I removed 1 screw pulled off 2 wires and place them on the new one. very easy and the repair storys really helped locating the problem

So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.