1106205802 Kenmore Washer - Instructions

All Instructions for the 1106205802
46 - 60 of 94

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken door actuator spring -interposer for motor control
1 of 2 people found this instruction helpful.
  • Stephen from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.
Was this helpful?
Thank you for voting!
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
2 of 5 people found this instruction helpful.
  • Patrick from Ramsey, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on a nd reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people found this instruction helpful.
  • Edward from Nanuet, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
Dryer would not come on
0 of 1 people found this instruction helpful.
  • Steven from Bassett, VA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this helpful?
Thank you for voting!
Leaking door gasket
1 of 4 people found this instruction helpful.
  • Don from Point Roberts, WA
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers
The door would not close after installing gasket. Used liquid soap around edge of gasket, this worked.
Was this helpful?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
0 of 1 people found this instruction helpful.
  • Larry from Elmhurst, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people found this instruction helpful.
  • linda from las cruces, NM
  • Easy
  • 15 - 30 mins
  • Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people found this instruction helpful.
  • Andris from Sands Point, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people found this instruction helpful.
  • Shirley from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people found this instruction helpful.
  • peggy ann from forest city, NC
  • Really Easy
  • Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
Dryer would not start
0 of 1 people found this instruction helpful.
  • Tim from Pepperell, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechan ical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)
Was this helpful?
Thank you for voting!
Dryer won't start!
0 of 1 people found this instruction helpful.
  • Richard from Paradis, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the drye r. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!
Was this helpful?
Thank you for voting!
the dryer would not turn on
0 of 1 people found this instruction helpful.
  • James from Shortsville, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab out 10 minutes.
Was this helpful?
Thank you for voting!
Dryer would not turn on, found metal clip in laundry
0 of 1 people found this instruction helpful.
  • Terry from Carlsbad, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ss fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
Was this helpful?
Thank you for voting!
All Instructions for the 1106205802
46 - 60 of 94