1106118821 Kenmore Dryer - Instructions

All Instructions for the 1106118821
121 - 135 of 183

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Couldnt get the dryer to turn on even when i had power.
0 of 1 people found this instruction helpful.
  • Kevin from Tonica, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!
Was this helpful?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
0 of 1 people found this instruction helpful.
  • Larry from Elmhurst, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this helpful?
Thank you for voting!
Broken clips
0 of 1 people found this instruction helpful.
  • Roger from Twinsburg, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. rei nstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!
Was this helpful?
Thank you for voting!
Dryer would not come on
0 of 1 people found this instruction helpful.
  • Steven from Bassett, VA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this helpful?
Thank you for voting!
Broken dryer door latch.
0 of 2 people found this instruction helpful.
  • Fred from Encino, CA
  • Really Easy
  • Less than 15 mins
Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would hav e been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.
Was this helpful?
Thank you for voting!
dryer door wouldnt latch shut
0 of 2 people found this instruction helpful.
  • Phyllis from Riva, MD
  • Really Easy
  • Less than 15 mins
  • Wrench set
ordered new latch kit and repaired, very easy thank you
Was this helpful?
Thank you for voting!
The dryer would not run.
0 of 2 people found this instruction helpful.
  • Kevin from North Aurora, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
Old Part Broke Off
0 of 2 people found this instruction helpful.
  • Steve from Edina, MN
  • Really Easy
  • Less than 15 mins
Took 5 seconds, just snapped in the slot, didn't need any tools.
Was this helpful?
Thank you for voting!
Dryer would not start
0 of 2 people found this instruction helpful.
  • Edwin from Shelby, NC
  • Easy
  • Less than 15 mins
  • Screw drivers
Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.
Was this helpful?
Thank you for voting!
door latch/ catch completely shattered
0 of 3 people found this instruction helpful.
  • Edward from Lowell, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken of f and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.
Was this helpful?
Thank you for voting!
Washer/Dryer would not start
  • James from Salt Lake City, UT
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.
Was this helpful?
Thank you for voting!
The small end of the actuator switch that the door pushes against was broken off.
  • Joyce from Highland Springs, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!
Was this helpful?
Thank you for voting!
Door Switch Actuator Spring/Lever & Door Catch Replacement
  • Charles from Marysvile, WA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Open the top and replaced the switch bracket with the actuator lever then inserted new door catch.
Was this helpful?
Thank you for voting!
actuator spring lever broke
  • george from port angeles, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clo thes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened
Was this helpful?
Thank you for voting!
All Instructions for the 1106118821
121 - 135 of 183