1106118821 Kenmore Dryer - Instructions

All Instructions for the 1106118821
91 - 105 of 183

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
my stovetop light did not work
1 of 2 people found this instruction helpful.
  • Geraldine M. from Fork Union, VA
  • Really Easy
  • 15 - 30 mins
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No applianc e store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
Door Gasket Broke into pieces
1 of 3 people found this instruction helpful.
  • Cheryl from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.
Was this helpful?
Thank you for voting!
Dryer won't start!
0 of 1 people found this instruction helpful.
  • Richard from Paradis, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the drye r. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!
Was this helpful?
Thank you for voting!
broken door catch. door wont close properly
0 of 1 people found this instruction helpful.
  • juan from los angeles, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.
Was this helpful?
Thank you for voting!
Dryer door would not close
0 of 1 people found this instruction helpful.
  • Felipe from Helotes, TX
  • Really Easy
  • Less than 15 mins
Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!
Was this helpful?
Thank you for voting!
Wife pulled bed sheets out of drier and broke door switch actuator
0 of 1 people found this instruction helpful.
  • Ernest from Moundsville, WV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.
Was this helpful?
Thank you for voting!
door wouldn"t close tightly
0 of 1 people found this instruction helpful.
  • Noreen from Fairfax, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
removed the broken part and replaced with the new one
Was this helpful?
Thank you for voting!
the dryer would not turn on
0 of 1 people found this instruction helpful.
  • James from Shortsville, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab out 10 minutes.
Was this helpful?
Thank you for voting!
Dryer would not turn on, found metal clip in laundry
0 of 1 people found this instruction helpful.
  • Terry from Carlsbad, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ss fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
Was this helpful?
Thank you for voting!
Dryer door wouldn't stay latched shut during cycle
0 of 1 people found this instruction helpful.
  • KRISTIN from DENVER, CO
  • Really Easy
  • Less than 15 mins
  • Pliers
In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!
Was this helpful?
Thank you for voting!
The switch in the door of the dryer was broken so it would keep running when you opened the door
0 of 1 people found this instruction helpful.
  • Matt from Stilwell, KS
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.
Was this helpful?
Thank you for voting!
Dryer stopped working
0 of 1 people found this instruction helpful.
  • Mike from Conway, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people found this instruction helpful.
  • linda from las cruces, NM
  • Easy
  • 15 - 30 mins
  • Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!
The dryer door kept popping open while in use.
0 of 1 people found this instruction helpful.
  • Joseph from Margate, FL
  • Easy
  • 15 - 30 mins
I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to ma ke this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...
Was this helpful?
Thank you for voting!
All Instructions for the 1106118821
91 - 105 of 183