- Home
- 1106118721
- Instructions
1106118721 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The switch in the door of the dryer was broken so it would keep running when you opened the door
0 of 1 people
found this instruction helpful.
-
Matt from Stilwell, KS
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a
... Read more
simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.
Read less
Was this helpful?
Thank you for voting!
Dryer stopped working
0 of 1 people
found this instruction helpful.
-
Mike from Conway, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th
... Read more
e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.
Advice: Don't slam the dryer door. The actuator will last longer.
Advice: Don't slam the dryer door. The actuator will last longer.
Read less
Was this helpful?
Thank you for voting!
latch not working on Kenmore dryer
0 of 1 people
found this instruction helpful.
-
sally from Houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Was this helpful?
Thank you for voting!
Wife pulled bed sheets out of drier and broke door switch actuator
0 of 1 people
found this instruction helpful.
-
Ernest from Moundsville, WV
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.
Was this helpful?
Thank you for voting!
Dryer door wouldn't stay latched shut during cycle
0 of 1 people
found this instruction helpful.
-
KRISTIN from DENVER, CO
- Really Easy
- Less than 15 mins
-
Pliers
In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!
Was this helpful?
Thank you for voting!
My dryer door would not stay shut.
0 of 1 people
found this instruction helpful.
-
Michelle from Colby, KS
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.
Was this helpful?
Thank you for voting!
the door switch broke, and I had to pop the lid unscrew the switch and use a clothespin to depress the switch acuator button....not pretty.
0 of 1 people
found this instruction helpful.
-
Greg from Phoenixville, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.
Was this helpful?
Thank you for voting!
Door latch broken
0 of 1 people
found this instruction helpful.
-
P from Melbourne Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.
Was this helpful?
Thank you for voting!
Door would not latch
0 of 1 people
found this instruction helpful.
-
Richard from Millinocket, ME
- Really Easy
- Less than 15 mins
-
Pliers
I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.
Was this helpful?
Thank you for voting!
Couldnt get the dryer to turn on even when i had power.
0 of 1 people
found this instruction helpful.
-
Kevin from Tonica, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!
Was this helpful?
Thank you for voting!
Dryer would not come on
0 of 1 people
found this instruction helpful.
-
Steven from Bassett, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this helpful?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
0 of 1 people
found this instruction helpful.
-
Larry from Elmhurst, IL
- Easy
- 30 - 60 mins
-
Screw drivers
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this helpful?
Thank you for voting!
Broken clips
0 of 1 people
found this instruction helpful.
-
Roger from Twinsburg, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. rei
... Read more
nstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!
Read less
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people
found this instruction helpful.
-
Andris from Sands Point, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Read less
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people
found this instruction helpful.
-
linda from las cruces, NM
- Easy
- 15 - 30 mins
-
Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!