1106117821 Kenmore Dryer - Instructions

All Instructions for the 1106117821
76 - 90 of 200

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
latch was broke
1 person found this instruction helpful.
  • Rick from SAN DIEGO, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person found this instruction helpful.
  • j from TAZEWELL, TN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person found this instruction helpful.
  • Tammy from glenford, OH
  • Very Easy
  • Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
Broken door switch
2 of 4 people found this instruction helpful.
  • john from el paso, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Susan from HUDSON, MA
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people found this instruction helpful.
  • satyavenkata from Bentonville, AR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person found this instruction helpful.
  • Billy from NEW BERN, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
door would stay closed
1 person found this instruction helpful.
  • william from KILLEEN, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
The door cables broke.
1 person found this instruction helpful.
  • Robert from Perris, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I replaced the springs and cables in the dryer door.
Was this helpful?
Thank you for voting!
Stepdaughter had over the years broke the 2 cables that supported the drop down door. So she let it hang by the hinges, which eventually broke them also.
1 person found this instruction helpful.
  • Thomas from LINCOLN, NE
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person found this instruction helpful.
  • Steven from New Richmond, WI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person found this instruction helpful.
  • Melody from TEXARKANA, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
Would not drain
1 person found this instruction helpful.
  • Robert from SANDWICH, IL
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people found this instruction helpful.
  • Rick from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people found this instruction helpful.
  • Daniel from TRENTON, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Was this helpful?
Thank you for voting!
All Instructions for the 1106117821
76 - 90 of 200