- Home
- 1106008713
- Instructions
1106008713 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken clips
0 of 1 people
found this instruction helpful.
-
Roger from Twinsburg, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. rei
... Read more
nstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!
Read less
Was this helpful?
Thank you for voting!
Broken dryer door latch.
0 of 2 people
found this instruction helpful.
-
Fred from Encino, CA
- Really Easy
- Less than 15 mins
Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would hav
... Read more
e been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.
Read less
Was this helpful?
Thank you for voting!
dryer door wouldnt latch shut
0 of 2 people
found this instruction helpful.
-
Phyllis from Riva, MD
- Really Easy
- Less than 15 mins
-
Wrench set
ordered new latch kit and repaired, very easy thank you
Was this helpful?
Thank you for voting!
Old Part Broke Off
0 of 2 people
found this instruction helpful.
-
Steve from Edina, MN
- Really Easy
- Less than 15 mins
Took 5 seconds, just snapped in the slot, didn't need any tools.
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
The dryer would not run.
0 of 2 people
found this instruction helpful.
-
Kevin from North Aurora, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in
... Read more
a few days. Problem solved. Thank you
Read less
Was this helpful?
Thank you for voting!
Dryer would not start
0 of 2 people
found this instruction helpful.
-
Edwin from Shelby, NC
- Easy
- Less than 15 mins
-
Screw drivers
Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.
Was this helpful?
Thank you for voting!
door latch/ catch completely shattered
0 of 3 people
found this instruction helpful.
-
Edward from Lowell, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken of
... Read more
f and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.
Read less
Was this helpful?
Thank you for voting!
Light bulb failure
-
Grant from Alexandria, VA
- Really Easy
- Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Door latch mechanism broke and fell into door
-
Peter from POTTSTOWN, PA
- Really Easy
- Less than 15 mins
Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.
Was this helpful?
Thank you for voting!
The spring lever broke at the bend after 26 years of use.
-
Mark from Crestview, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.
Was this helpful?
Thank you for voting!
not enough heat to dry clothes
-
James C. from Cobbs Creek, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James
Was this helpful?
Thank you for voting!
dry door latch broke
-
George from Melbourne, FL
- Really Easy
- Less than 15 mins
-
Pliers
I watched the online video first, which made the removal and installation fast and easy.
Was this helpful?
Thank you for voting!
The catch on the dryer door had to be replaced
-
Vincent A. from Gibsonia, PA
- Really Easy
- Less than 15 mins
-
Pliers
Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.
Was this helpful?
Thank you for voting!
Dryer would not start
-
John from Sackets Harbor, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came a
... Read more
cross your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!
Read less
Was this helpful?
Thank you for voting!