1105905850 Kenmore Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Parts Used:
-
Judith from Phoenix, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced oven lightbulb
-
peggy ann from forest city, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light burned out in upper oven
-
Shirley from Las Vegas, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Parts Used:
-
Janet from Ada, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing lid hinge bearing
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Parts Used:
-
Kim from Oviedo, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Parts Used:
-
Grant from Alexandria, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Washer leaking
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Parts Used:
-
Forrest from Oxford, AL
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Had issues with removing the inner tub
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
Parts Used:
-
Bruce from Yankton, SD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!