110458 Kenmore Washer - Instructions

All Instructions for the 110458
106 - 120 of 253

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Tub filling when power was off due to inlet valve leak.
3 of 3 people found this instruction helpful.
  • Francisco from DELTONA, FL
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Followed instructions as shown on repair video at site.
Was this helpful?
Thank you for voting!
tub would not turn
3 of 3 people found this instruction helpful.
  • claude van from big sandy, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this helpful?
Thank you for voting!
Pump not working
4 of 6 people found this instruction helpful.
  • Darrell from Lady Lake, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replaced pump
Was this helpful?
Thank you for voting!
door would not latch , and lights on front just flashed
5 of 9 people found this instruction helpful.
  • FRANCIS from leesburg, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.
Was this helpful?
Thank you for voting!
Small water leak into washer when not being used
4 of 6 people found this instruction helpful.
  • Thomas from Dallas, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged and disconnected water lines. Removed three machine screws on the back edge of the washer top. Lifted the back and then pulled it to release it from the front. Removed 1 screw from the back next to the hot water connection. Slide the water valve assembly over to the left if you are standing in front of the washer and it pops out. Then slide the hose clamp for the small hose off and use flat head screw driver to pry hose loose. Then use flat head to gently work connectors off. Then reinstall everything in reverse order. Reconnect water lines turn on water and watch water leaks before cover is reinstalled.
Was this helpful?
Thank you for voting!
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
4 of 7 people found this instruction helpful.
  • Keith from Amherst, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into plac e and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
Was this helpful?
Thank you for voting!
the pump wasnt puping out the water
3 of 4 people found this instruction helpful.
  • Evette from Mayfield, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Socket set
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this helpful?
Thank you for voting!
water was back filling into the tub when not in use
3 of 4 people found this instruction helpful.
  • Larry from BONAIRE, GA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it t o the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.
Was this helpful?
Thank you for voting!
drum baffle broke and had to be replaced
3 of 4 people found this instruction helpful.
  • Alan from GOUVERNEUR, NY
  • Really Easy
  • Less than 15 mins
place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum
Was this helpful?
Thank you for voting!
The washing machine was not draining. It was showing a code on the washer of 02.
3 of 4 people found this instruction helpful.
  • Robin from Gary, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Was this helpful?
Thank you for voting!
I find water in the drum after a few days of non use
3 of 4 people found this instruction helpful.
  • Anthony from Brooklyn, NY
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.
Was this helpful?
Thank you for voting!
Washer leaking
3 of 4 people found this instruction helpful.
  • Carolyn L. from CLAYTON, NY
  • Really Easy
  • 30 - 60 mins
Followed internet instructions
Was this helpful?
Thank you for voting!
Bellow leaking water
3 of 5 people found this instruction helpful.
  • Eric from Vacaville, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Was this helpful?
Thank you for voting!
Washer had a 'thunk' sound during washing. I removed the back and saw the broken shock.
2 of 2 people found this instruction helpful.
  • Jeffrey from Bothell, WA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
1. After ordering I watched the video on the page for the part, the guy showed exactly what to do.
2. The day the part was to arrive I leaned the washer back and opened the lower front, based on the video on the page for the part, and removed the old shock absorber.
3. Part arrived, and I put in the new shock.
4. I ran a li ght load in the washer and it worked.
5. I put the washer back together and put in place.
6. I have since run a full load and it has worked well.

Note: In case I messed up the shock I was putting in, I bought 2 but did not need the 2nd one. I have kept it, just in case my 20 year old Whirlpool might need another one in the future.
Was this helpful?
Thank you for voting!
Tub would get out of balance on the spin cycle
2 of 2 people found this instruction helpful.
  • Kirk from P C BEACH, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
UNPLUG WASHER ,SLIDE WASHER OUT FROM THE WALL. TAKE THE BACK OFF ,THEN TAKE PANET OFF IN THE FRONT. TWIST OLD SHOCKS ON THE TOP FIRST THEN TWIST BOTTOMS AND THE SHOCK WILL CUM OUT. PUT NEW SHOCK IN BOTTOM FIRST TWIST TILL YOU HEAR OR FEEL THE SHOCK SEAT ITSELF THEN INSTALL ON THE BOTOOM OF THE TUB.
Was this helpful?
Thank you for voting!
All Instructions for the 110458
106 - 120 of 253