110458 Kenmore Washer - Instructions

All Instructions for the 110458
91 - 105 of 253

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bent slide on pedestal
5 of 8 people found this instruction helpful.
  • Donald from Greenfield, WI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Note that the problem was with the pedestal, not the washing machine. In the process of attaching the two units together, the drawer in the pedestal is removed. When I tipped the assembly up, the slide slid out and locked horns with an object, bending the slide. The slide is an easy replacement. Just one screw holds it in place. A sl ot in the slide mates with a tab to hold the back side of the slide in place.
Was this helpful?
Thank you for voting!
Bellow was damaged,water leakage.
5 of 8 people found this instruction helpful.
  • Gopaul from Queens, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this helpful?
Thank you for voting!
Pump not draining the water out.
4 of 5 people found this instruction helpful.
  • Martin from Kotzebue, AK
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
Was this helpful?
Thank you for voting!
Door latch would not lock
4 of 5 people found this instruction helpful.
  • William from Victorville, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.
Was this helpful?
Thank you for voting!
The door bellows had a cut in it
4 of 5 people found this instruction helpful.
  • Arthur from MORGANTOWN, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this helpful?
Thank you for voting!
Ripped bellowspul
4 of 5 people found this instruction helpful.
  • WILLIAM from REPUBLIC, MO
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this helpful?
Thank you for voting!
Spring balanced tub violent shake on spin
4 of 5 people found this instruction helpful.
  • Paul from TARPON SPGS, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement bro ke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people found this instruction helpful.
  • Helen from NASHUA, NH
  • Really Easy
  • 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
3 of 3 people found this instruction helpful.
  • john from YARDLEY, PA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Socket set
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Was this helpful?
Thank you for voting!
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
3 of 3 people found this instruction helpful.
  • Dennis from AUSTIN, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disc onnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Was this helpful?
Thank you for voting!
The video supplied by you was great and it worked very well.
3 of 3 people found this instruction helpful.
  • Michael from NEWBERG, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
It was fast and pretty easy to do.
Was this helpful?
Thank you for voting!
Replace Bellows between door and tub
5 of 9 people found this instruction helpful.
  • Gerald from Douglas, AL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Was this helpful?
Thank you for voting!
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
3 of 3 people found this instruction helpful.
  • anthony from EASTPOINTE, MI
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was do ne.
Was this helpful?
Thank you for voting!
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
3 of 3 people found this instruction helpful.
  • scott from DENVER, NC
  • Really Easy
  • Less than 15 mins
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
Was this helpful?
Thank you for voting!
Low water flow into dispenser and washer tub
3 of 3 people found this instruction helpful.
  • Daniel from WAKE FOREST, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Super simple repair, videos on this site were spot-on.

1. Turn off water, unplug washer, and disconnect the hoses from the back of the washer.
2. Remove the three T20 torx screws holding on the top of the washer, slide the top back about an inch, and lift off.
3. Remove the T20 torx screw holding the water valve to the back plate of the washer.
4. Using pliers, release the hose clamp on the outlet hose of the valve and slide it down about an inch.
5. Remove the old valve and attach the new one to the outlet hose. Reinstall the hose clamp.
6. Replace the screw that holds the valve to the back plate and reinstall the top of the washer. Reconnect hoses the the washer, turn on water, and plug back the washer back in.
7. Odds are, your water flow has been low for a while and the first cycle is going to flush a good bit of mildew and other gunk into the washer drum. Run a cleaning cycle with about 1/3 cup bleach through the washer prior to using.

Should be good to go!
Was this helpful?
Thank you for voting!
All Instructions for the 110458
91 - 105 of 253