11042932200 Kenmore Washer - Instructions

(1) Turn off water valves (2) remove water lines (3) remove three metric star screws from top/back of washer (4) remove to plate (5) remove single screw retaining water inlet valve at back of washer (6) remove electrical connections from water inlet valve and flow meter (7) loosen hose clamps at back of soap dispenser (8) remove assembly/ ... Read more apply new parts (9) reverse above directions. Because the plastic nipple at the back of the soap dispenser was brittle, it partially broke on me. I applied urethane glue to the break and let it dry overnight. Next day I applied marine-grade silicone sealant around the break area. That evening I assembled and then used the washer to test for leaks. Success!

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 ... Read more removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs ... Read more will be purchased here.

I saw a u tube video and followed the presenters instructions. Very simple instruction very simple repair. The whirlpool duet is a well designed machine with the mechanical parts easily accessible. I know if if would have had a professional service come and repair if it would have cost several hundred dollars. It cost me the parts, $5 ... Read more 0. 00 (That was for the 3-pack of baffles), 1 beer and my time. "Easy fix".

Removed 3 screws from back to remove top. Then 1 screw to release the valve from the back. Take off hose spring clamp remove hose, then do it all in reverse oder. It was a snap.

After diagnosing codes noticed no drain replaced pump asm

Removed top cover. Manually opened door through top cover opening. Removed 3 screws at front holding assembly. Removed 3 harnesses attached to assembly. Replaced with new assembly and screwed back in. Replaced harnesses. Certainly an easy DIY job.

I did not replace the pump body. I just removed the motor with the 3 screws. Put the new one on. This way I did not need to mess with the hose clamps.

Replace old part

replaced drain pump.Saved 200$

Used nut driver to remove 3 screws from rear of washer and remove washer top. Used Torx driver to remove single screw holding valve assembly in place. Loosened hose clamp with adjustable pliers and then unplugged 6 electrical plugs. Reversed process to put everything back together. Very simple.

1. Unplugged washer. 2. Turned off water supply valves. 3. Disconnected water supply hoses from back of washer. 4. Removed three (3) screws that secure top of washer from top/back of washer. 5. Removed top of washer. 6. Disconnected water outlet line from old inlet valve assembly by releasing clamp. 7. Labeled and disconnected spade conne ... Read more ctions from old inlet valve. 8. Removed single (1) screw securing old inlet valve in place and removed valve from washer. 9. Re-assembled using new inlet valve lickety split faster than a five-legged skunk.

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. ... Read more Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Baffle just snapped into place. . . . . So easy!