11033 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer would not heat up
-
Bruce from Feeding Hills, MA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.
Was this helpful?
Thank you for voting!
Dryer would not heat, igniter not glowing
-
David from Orchrd Park, NY
- Easy
- Less than 15 mins
-
Wrench (Adjustable)
First disconnect power to the machine. Remove lower access door locate the igniter connector and disconnect it. Now, remove the screw holding the igniter to the mounting bracket with a 5/16" box wrench, carefully remove the igniter. Replace the old mounting bracket but first start the igniter mounting screw in the new bracket, threadin
... Read more
g it in all the way and then removing it to make installation easier. Install the new bracket and then the igniter, Be very careful, the igniter is fragile. Holding the igniter securely, install the mounting screw. Reconnect the wire connector replace lower door and plug the machine in. Voila! heat!!
Read less
Was this helpful?
Thank you for voting!
Gas burner would shut off or not ignite
-
Stephen from Grand Haven, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Found symptoms on Part Select website and confirmed that the problem was the coils. It was extremely easy to find and the site saved me hundreds of dollars on a repairman, labor costs and marked up parts. It literally took about 5 minutes to repair. Awesome site!!Thank You
Was this helpful?
Thank you for voting!
gas dryer heating intermittent
-
terrence from irving, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
1)Pulled electrical connectors off each of two gas valve coils. 2)Removed two Phillips screws and removed coil retainer bracket. 3)Lifted off two old coils and replaced with two new coils. 4)Replaced coil retainer bracket and plugged back connector on each coil; total coil replacement time is less than two minutes. 5)Confirmed gas valv
... Read more
e opens and gas ignites every time over a two day test period. 6)Re-installed door. Wife Happy. We spent under $20 for 'M' series new style coil kit; and the $7 shipping got it here in two days. What a deal! Terry Rahmer 8.24.2012
Read less
Was this helpful?
Thank you for voting!
Dryer would heat up, then cool off.
-
Sandra from Chicago, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
After researching the problem, I thought the solution would be to replace the two terminal coil valve, but wasn't 100% sure it wasn't the 3 terminal coil, so I bought both. the dryer is 13 years old so I thought it deserved new coils. My husband was away for the week and I had about 10 loads of laundry to do. I dreaded the thought of g
... Read more
oing to the laundromat, so I went ahead and ordered the parts, thinking I would call a handyman to install them once they arrived. However, I found a Youtube video showing exactly what I had to do and thought it looked easy enough. I unplugged the machine, removed the front hatch and the 2 small screws holding the coils in place. I unplugged the old coils, used a vacuum to remove the dust in the area and installed the new coils. I popped them back into place, screwed them in, replaced the hatch, plugged the machine in, and VOILA!!!! A dryer that heats!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
no heat
-
Edward from Benton Harbor, MI
- Easy
- 15 - 30 mins
-
Screw drivers
the repair was an easy fix, I removed the two screws from the brackets holding the coils, disconnect and removed them installed the new coils connected plugs turned on dryer and I got heat not bad at all thank you for the help
Was this helpful?
Thank you for voting!
dryer wouldn't heat
-
michael from Pueblo, CO
- Easy
- 15 - 30 mins
-
Screw drivers
Watched video. Made this a very easy repair.Will use this site for next repair.
Was this helpful?
Thank you for voting!
NO Heat in dryer
-
diane from Oak forest, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
It Went well Part was very fragile
Was this helpful?
Thank you for voting!
burner wouldn't relight after 1st or 2nd heat cycle; in other words heat faded out; solenoids measured correct resistance, but would not open the valves once they heated up
-
David from Adkins, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed frt cover & drum, replaced solenoids, cleaned the unit interior
Was this helpful?
Thank you for voting!
Dryer would heat, initially, but would not come back on
-
Kevin from BRAINTREE, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
My suggestion is to read all of the items that may result in no heat, or insufficient heat, you will find your problem in one of the reply's and the right part to replace. The repair was made much easier, as I installed a Maintenance kit at the same time. Drum rollers, drive belts and tensioner. With the drum out, the coil retaining cli
... Read more
p was a LOT easier to re-instal. If the drum isn't out, you can lift the drum up a little and squeeze a stubby screw driver in to loosen the retaining screws. You have to use the proper size screwdriver so you don't strip the screws, and maybe a pair of gas pliers around the handle of the screwdriver to give it a little torque to help loosen the screws, while keeping downward pressure on the screwdriver.
Read less
Was this helpful?
Thank you for voting!
dryer didn't heat up
-
Jaime from Glendale Heights, IL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Pretty much just followed the installation video. Took dryer apart and just put everything back the way it was.
Was this helpful?
Thank you for voting!
Dryer runs but no heat
-
David from Epping, NH
- Easy
- 15 - 30 mins
-
Nutdriver
Viewed online then found part and ordered it in, took front off of dryer and cleaned out the dryer. replaced igniter seemed to work but ended up having to replace thermial fuse.
Was this helpful?
Thank you for voting!
Starts and runs, no heat
-
Rick from Paso Robles, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Initially thought it was the thermal fuse since that has already been replaced twice before for the same type of problem. After replacing the fuse the same issue remained, so I did a little hunting on the internet and found some matrixes to help diagnose the issue. After a couple of minutes, I discovered it was the ignitor. I immediately
... Read more
ordered the part and received it in about 5 business days. Even though that took longer than previous orders (usually < 3 days), I was still happy to get the part at a MUCH cheaper price than available locally. Installation took about 5 minutes with only a 5/16" nut driver and we were back in business. Kind of glad it broke because the dryer needed a good de-linting and cleaning anyway. : )
Read less
Was this helpful?
Thank you for voting!
Dryer would not heat.
-
Henry from Weston, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
Checked heating element and it glowed so I replaced the ceramic gas valve regulators. 4 screws to take front off the dryer and 2 screws to replace part. Couldn't have been easier but I wouldn't have been able to do it without watching the video first.
Was this helpful?
Thank you for voting!
dryer heats up for seconds and stat cold
-
donald from anchorage, AK
- Easy
- Less than 15 mins
-
Screw drivers
open the back pannel and use multimeter to check the wirings and everything checks ok. open the bottom front panel of the dryer and turn the dryer on. the igniter works and the flame came out for seconds and dies off. the igniter keep coming on, but it seems that the gas was not coming out. i checked the gas line valve and it was open. i
... Read more
had a good idea it wasn't the wiring or the gas line, it must be the coil-valve,(safety coil), that letting the gas flow. i order the parts, it came sooner, which is good, and it took me less than 10 minutes to install, and i only use a philip screw driver. i thank you for sending me the right part in short period of time.
Read less
Was this helpful?
Thank you for voting!