11033 Kenmore - Overview

Models starting with 11033

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
M Series New Style Coil Kit – Part Number: 279834
$36.25
In Stock
M Series New Style Coil Kit
★★★★★
★★★★★
(43)
Part #279834
This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
Igniter Kit – Part Number: 279311
$51.90
In Stock
Igniter Kit
★★★★★
★★★★★
(13)
Part #279311
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 4" wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers.
Gearcase – Part Number: 3360629
$546.62
In Stock
Gearcase
★★★★★
★★★★★
(8)
Part #3360629
This is used in your direct drive washer that has a neutral drain.
Spin Pinion Seal – Part Number: WP356427
$14.25
In Stock
Spin Pinion Seal
★★★★★
★★★★★
(1)
Part #WP356427
This seal is for the top of basket drive tube shaft.
Screw – Part Number: WP488729
$10.50
In Stock
Screw
Part #WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
Washer Gear Case Cover Seal – Part Number: WP3349985
$30.75
In Stock
Washer Gear Case Cover Seal
★★★★★
★★★★★
(2)
Part #WP3349985
This part prevents the agitator shaft from leaking oil onto the transmission.
NEUTRAL DRAIN KIT – Part Number: 388253A
$79.02
In Stock
NEUTRAL DRAIN KIT
★★★★★
★★★★★
(1)
Part #388253A
The neutral drain kit prevents the basket from spinning during the drain cycle.
Oil Seal Kit for Gearcase Input Shaft – Part Number: 285352
$59.35
In Stock
Oil Seal Kit for Gearcase Input Shaft
★★★★★
★★★★★
(1)
Part #285352
This two piece oil seal kit comes in two pieces and is used for the gearcase input shaft of your washer.
Shaft, Agitator (Complete) – Part Number: WP389387
$268.55
Special Order
Shaft, Agitator (Complete)
★★★★★
★★★★★
(1)
Part #WP389387
This kit is used for direct drive washing machines and is found inside the gearcase.
Screw – Part Number: WP693995
$9.85
In Stock
Screw
Part #WP693995
Dryer Screw – Part Number: WP681414
$10.95
In Stock
Dryer Screw
Part #WP681414
This screw is sold individually.
Gas Valve Kit – Part Number: 279923
$297.31
In Stock
Gas Valve Kit
★★★★★
★★★★★
(1)
Part #279923
This gas valve kit comes with the wiring harness.

Exact Part matches for your search term

Instructions – Part Number: 11033
No Longer Available
Instructions
This part number matches the current model number 11033
Part #11033
BATTERY PK. 14.4V – Part Number: 11033
No Longer Available
BATTERY PK. 14.4V
This part number matches the current model number 11033
Part #11033

Common Symptoms of models starting with 11033

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer ran but would not heat
422 of 482 people found this instruction helpful.
  • Gary from Haverhill, NH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Was this helpful?
Thank you for voting!
Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.
220 of 248 people found this instruction helpful.
  • andy from Bethesda, MD
  • Easy
  • 30 - 60 mins
  • Screw drivers
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was corrected.
Was this helpful?
Thank you for voting!
Timer wasn't working (New Timer)
168 of 214 people found this instruction helpful.
  • Joaquin from Las Vegas, NV
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.
Was this helpful?
Thank you for voting!