11033 Kenmore - Instructions

All Instructions for the 11033
31 - 45 of 214

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would not heat or turn off
9 of 12 people found this instruction helpful.
  • michael from eldridge, IA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
removed front of dryer located igniter removed two screws disconnected wires then put new one in also replace thermal fuse and thermostat on back of dryer works great.
Was this helpful?
Thank you for voting!
gas dryer would fire, but shut down before getting warm enough to dry clothes
7 of 7 people found this instruction helpful.
  • Glenn from Ossian, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set, Wrench set
Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. The n closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.
Was this helpful?
Thank you for voting!
Dryer not Drying
8 of 10 people found this instruction helpful.
  • Manuel from Jurupa Valley, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.
Was this helpful?
Thank you for voting!
No Heat After 10 Minutes
7 of 8 people found this instruction helpful.
  • lawrence from GROTON, VT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench set
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people found this instruction helpful.
  • Ken from Bixby, OK
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Was this helpful?
Thank you for voting!
not heat
7 of 10 people found this instruction helpful.
  • Sarah from Merrimac, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on t he tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.
Was this helpful?
Thank you for voting!
Dryer had no heat at all. This is an older gas dryer.
5 of 5 people found this instruction helpful.
  • todd from MILFORD, PA
  • Really Easy
  • Less than 15 mins
  • Wrench set
Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuit y. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.
Was this helpful?
Thank you for voting!
No heat, would not light because igniter burnt out
6 of 8 people found this instruction helpful.
  • anthony from Port Arthur, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Was this helpful?
Thank you for voting!
not drying all the way, not getting hot enough
6 of 8 people found this instruction helpful.
  • robert from cedar lake, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on
Was this helpful?
Thank you for voting!
Dryer would only heat at start up for one cycle
6 of 8 people found this instruction helpful.
  • Rob from Henderson, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no o hm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!
Was this helpful?
Thank you for voting!
Dryer would not heat up properly. It would heat initially but once the heat was off it would not come on again.
5 of 6 people found this instruction helpful.
  • Joseph from Chicago, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (a nd the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.
Was this helpful?
Thank you for voting!
No Heat sometimes, But for a moment then None
4 of 4 people found this instruction helpful.
  • Scott from Sacramento, CA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i d ecided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.
Was this helpful?
Thank you for voting!
Gas dryer would not heat - pilot lit briefly then went off
5 of 7 people found this instruction helpful.
  • William from Chicago, IL
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
Was this helpful?
Thank you for voting!
The washer would drain, but was screaming while doing nothing else.
4 of 4 people found this instruction helpful.
  • Richard from JAMESTOWN, PA
  • Really Easy
  • More than 2 hours
The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The ne wly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
Was this helpful?
Thank you for voting!
would only heat for about 7 minutes.
4 of 5 people found this instruction helpful.
  • Craig from ARMA, KS
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I replaced the thermos fuse, thermostat, igniter kit, and the M series
new style coil kit. The problem was the M series coil kit. I replaced
the other parts because this dryer is over 10 years old. I also brought
the radiant flame sensor. I spent $126.19 in parts plus shipping. If I just
just replaced the coil kit it would have 18.61 plus shipping. A new gas dryer like I have would cost about $459.00. I hope to get many more years out of this dryer. The hardest part of this repair for me was getting the front panel back on. I saved the parts that were good for futher repairs. I replaced the drum belt several years ago, still looks in good shape. I think this is a great DIY site. Just follow their instrutions. Somtimes I'll take a picture of the part before I remove it, just to be sure I replace it right.
Was this helpful?
Thank you for voting!
All Instructions for the 11033
31 - 45 of 214