11031652020 Kenmore Washer - Instructions

Prepare:
Before you start turn off the hot and cold water supply. Then remove the supply lines from the back of the washer. You may want a bucket to catch any remaining water in the supply lines.

Replace water inlet valve:
First, remove screws from upper back plate to release the control panel and the washer top.
... Read more />
Second, slide washer top to the front of the washer about 1/2 - 1 inch. This will allow you to raise the washer top.

Third, from underneath the washer top release the control panel by disengaging the locking clips near the back of the control panel.

Fourth, lay the top back in to the forward position and hinge the control panel from back to front. This will release the control panel.

Fifth, Disengage the wire harness for the control non. And remove the control panel completely.

Sixth, remove the wiring harness from the water inlet valve located on the left hand side, the. Remove the screws holding the valve in place.

Seventh, Install new valve, reconnect all of the wiring harnesses, reconnect the control Bob wire harness, and reinstall the control panel. It should click into place just as it came out.

Eighth, Slide the washer top back into place. Reinstall the back plate and screws.

Finish:
Finally reinstall the supply lines and turn on the water.

If you take the back off the machine, it's a lot easier to detach the control bridge. Saved a lot of time and did not need to stretch your fingers

Turn off water and remove inlet hoses
Remove of control Tower
Remove control tower and unplug from rest of washer
Remove water inlet valve and install new valve
Reverse operations

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Untwisted it and slipped the new one in quick and easily in less than a minute

Removed Back and top of digit front. removed water intake valve part order new part replacing was a breeze

It easily installed with a twist lock removal and installation. 2 minute fix.

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. ... Read more The hose clip could then be tightened without deforming the hose. Worked great with no leaks.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I used a small flat head screwdriver inserted into slots just under the cap and pried off the cap. The cap should come off very easy.
Replace with the new cap.

I used needle nose pliers to remove the broken piece of the latch from the lid lock and removed the round broken latch assembly from the lid by twisting counter clockwise and removing it from the round inset hole on the underside of the lid.

I then took the replacement latch assembly, inserted it flush in the hole and twiste ... Read more d it clockwise until it snapped into position. It took less than a minute to fix. The latch is very thin, made of plastic, so I bought two, to have an extra as a backup.

I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May

Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.

At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you