110271 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Smelled a burning odor occasionally
17 of 23 people
found this instruction helpful.
-
Paul from E NORTHPORT, NY
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set, Wrench (Adjustable)
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash
... Read more
er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Read less
Was this helpful?
Thank you for voting!
Washer lid would not release
18 of 26 people
found this instruction helpful.
-
Michael from BURLINGTON, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,
Was this helpful?
Thank you for voting!
leaking drain pump. Obviously a common problem with this washer
15 of 17 people
found this instruction helpful.
-
John from Solana Beach, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the we
... Read more
bsite parts diagram and whole website design is good.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people
found this instruction helpful.
-
Chuck from South Holland, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
Washer did not spin.
15 of 18 people
found this instruction helpful.
-
Matt from Sussex, WI
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
First I removed the two screws on the back side of the switch panel and tilted it back to expose the controls. I then pryed up the top of the washer to expose the lid switch. This was a mistake because I damaged the clips and bent the metal frame. Anyway after that I unlatched the lid switch on the top side, pulled it through the botto
... Read more
m, removed two screws holding the lid switch in place and replaced the switch and lid switch strike. Because I wrecked the machine top I had no alternative but to drill two holes from the top and put two screws in to hold the top down. It's ugly but it works.
The best part of all this is I received the part so fast that I was able to keep up the pace of doing laundry with no interruption. Thanks for being so reliable and quick to deliver. I already told many people about your service!
The best part of all this is I received the part so fast that I was able to keep up the pace of doing laundry with no interruption. Thanks for being so reliable and quick to deliver. I already told many people about your service!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
17 of 24 people
found this instruction helpful.
-
Kevin from Disputanta, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's
... Read more
lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Read less
Was this helpful?
Thank you for voting!
coin in drain pump put a hole in casing
15 of 19 people
found this instruction helpful.
-
jon from hannibal, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set
unscrew all the screws on the back of your cabrio washer just the bottom portion to access the drain pump which is located on bottom left underside of the wash drum, the drum on mine is plastic or plastic shroud i guess , theres 3 screws that hold the pump into place, also 2 hose clamps, and the power source, the cap that covers the power
... Read more
source is a bit of a pain to unsnap do this part last cause you'll be able to pull it out from under the drum and get to it easier. once the pump is free just do everything in reverse and you'll be good to go in about 30 to 40 mins . one more thing dont try to caulk or seal on the one thats broke its a lost cause just replace it and make sure like i have been lol no coins left in your pockets before they get washed......whirlpool cabrio other number i got off sticker besides model number is type 580 hope this is helpfull
Read less
Was this helpful?
Thank you for voting!
Lid Switch broke off at screws
13 of 13 people
found this instruction helpful.
-
Dale from West Branch, MI
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
First off it was much easier after watching the video that was on PartSelect website. It was a very good description of how to do the repair. The main thing is to have enough room to be able to move the washer around and be able to get around it.. Our washer and dryer are in our 1/2 bath so we had to completely unhook the dryer to move
... Read more
it out of the way to have room to work around the washer.. It was still a tight squeeze but it was pretty quick and easy once we got the area where the lid switch is attached. The only trouble we had was putting the front of the washer back on the tub correctly. That was mainly in part with not having enough room to move around. It was easy enough that is was worth saving the service call from the repairman. The most help was watching the video. Thanks PartSelect for your help.
Read less
Was this helpful?
Thank you for voting!
water leaking from pump
15 of 19 people
found this instruction helpful.
-
michael from westmoreland city, PA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Read less
Was this helpful?
Thank you for voting!
Broken Lid Switch
13 of 14 people
found this instruction helpful.
-
Andrew from San Rafael, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Washing machine is in a closet - tight space - was able to disconnect switch panel following other instructions, 2 screws on back, vertical // 2 screws near top corner on back, horizontal.
Pulled switch box off, could not get top sheet of washer off though, needed to detach side panel from back panel and lean the washing machin ... Read more e exterior panels fwd, and reach in from the back to disconnect the swicth ground, then pulled the lines, and disconnected the switch.
Then while still leaning the unit fwd, reconnected the ground for the new switch assemply, got it in the small clips leading back to control panel, fed the switch back into the control panel and reconnected.
Then, leaned unti back into place and got the panels lined up again, reset the control box, fiddles with the s clamps, and just tightened up the 4 screws.
Done.
Pulled switch box off, could not get top sheet of washer off though, needed to detach side panel from back panel and lean the washing machin ... Read more e exterior panels fwd, and reach in from the back to disconnect the swicth ground, then pulled the lines, and disconnected the switch.
Then while still leaning the unit fwd, reconnected the ground for the new switch assemply, got it in the small clips leading back to control panel, fed the switch back into the control panel and reconnected.
Then, leaned unti back into place and got the panels lined up again, reset the control box, fiddles with the s clamps, and just tightened up the 4 screws.
Done.
Read less
Was this helpful?
Thank you for voting!
Machiine would fill with water and then stop cycle. I determined that it was the lid switch because that is the sam e thing th emachine does when the lid is up.
15 of 20 people
found this instruction helpful.
-
Louise from Bridgewater, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
Followed some very handy instructions I found on the web.
First unplug machine and next back off the screws in the back of the plastic end caps holding down the control panel.
Then slip a putty knife under each of the front corners to release the panel so it can flip back
exposing the lid switch wiring harness clip c ... Read more onnector.
Release the lid switch clip connector from the wiring harness.
Next release the two brass colored clips that hold the top to the sides.
Remove sides.
Remove screws holding lid switch and unclip switch from back of top nd from under top .
Remove switch and replace with new one.
Reverse order reassembly making sure the four base tabs of the sides are in the four slots in the machine base frame.
Reinstall brass clips.
Make sure new switch is clipped to the control panel harness.
Screw down corner screws in control panel end caps.
Done.
Thank you PartsSelect for your pormpt, courteous, and informative service.
You also had the lowest price and fastest delivery.
Well done!
First unplug machine and next back off the screws in the back of the plastic end caps holding down the control panel.
Then slip a putty knife under each of the front corners to release the panel so it can flip back
exposing the lid switch wiring harness clip c ... Read more onnector.
Release the lid switch clip connector from the wiring harness.
Next release the two brass colored clips that hold the top to the sides.
Remove sides.
Remove screws holding lid switch and unclip switch from back of top nd from under top .
Remove switch and replace with new one.
Reverse order reassembly making sure the four base tabs of the sides are in the four slots in the machine base frame.
Reinstall brass clips.
Make sure new switch is clipped to the control panel harness.
Screw down corner screws in control panel end caps.
Done.
Thank you PartsSelect for your pormpt, courteous, and informative service.
You also had the lowest price and fastest delivery.
Well done!
Read less
Was this helpful?
Thank you for voting!
Agitator moves freely in both directions
14 of 18 people
found this instruction helpful.
-
James from NAPERVILLE, AL
- Really Easy
- Less than 15 mins
-
Wrench set
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and
... Read more
pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Read less
Was this helpful?
Thank you for voting!
water leaking during run cycle
13 of 15 people
found this instruction helpful.
-
michael from weymouth, MA
- Really Easy
- 15 - 30 mins
-
Pliers
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer
Was this helpful?
Thank you for voting!
Worn out splines connecting transmission driveshaft to agitator.
13 of 15 people
found this instruction helpful.
-
Thomas from MILLBURY, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an
... Read more
accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.
Read less
Was this helpful?
Thank you for voting!
Washer vibrates excessively on spin cycle
13 of 15 people
found this instruction helpful.
-
Glenn from PROVO, UT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and di
... Read more
d that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!