110260 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
bad lid swithch, problem with spin cycle
22 of 32 people
found this instruction helpful.
-
Bill from Beaver Dam, KY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
remove 2 screws that hold timer section
remove large clips that hold lid section
repace lid swich and put back together
works good
remove large clips that hold lid section
repace lid swich and put back together
works good
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people
found this instruction helpful.
-
Charmaine from Slidell, LA
- Easy
- 15 - 30 mins
-
Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people
found this instruction helpful.
-
Donald from Fredericksburg, VA
- Really Easy
- 15 - 30 mins
-
Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo
... Read more
ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Read less
Was this helpful?
Thank you for voting!
Agitator did not rotate properly
18 of 21 people
found this instruction helpful.
-
Tenel from The Woodlands, TX
- Easy
- 30 - 60 mins
-
Pliers, Socket set
1. Removed the softener dispenser
2. Removed the cap covering the clutch dogs and the bolt holding it all in place.
3. Removed the bolt holding the two agitator pieces and the clutch dogs together.
4. Removed the two agitator parts.
5. Replaced the clutch dogs.
6. Reassembled and put the bolt back in place.< ... Read more br />7. Replaced the gasket on the cover that goes over the clutch and bolt.
8. Replaced the softener dispenser
Very easy!
2. Removed the cap covering the clutch dogs and the bolt holding it all in place.
3. Removed the bolt holding the two agitator pieces and the clutch dogs together.
4. Removed the two agitator parts.
5. Replaced the clutch dogs.
6. Reassembled and put the bolt back in place.< ... Read more br />7. Replaced the gasket on the cover that goes over the clutch and bolt.
8. Replaced the softener dispenser
Very easy!
Read less
Was this helpful?
Thank you for voting!
My washer lid lock light kept blinking and the washer would not start
17 of 18 people
found this instruction helpful.
-
Janice from GREENVILLE, NC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the online video, removed the old part and replaced it with the new part. My washer is working perfectly. It took about an hour to reset.
Was this helpful?
Thank you for voting!
Making loud noises.
21 of 30 people
found this instruction helpful.
-
Roy from BROOKLYN, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Thank you
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people
found this instruction helpful.
-
Richard from EL SEGUNDO, CA
- A Bit Difficult
- More than 2 hours
-
Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE
... Read more
DO THE STEP AND REPEAT
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people
found this instruction helpful.
-
floyd from Slidell, LA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people
found this instruction helpful.
-
Dennis from Oak Island, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
Top section of agitator not turning
17 of 20 people
found this instruction helpful.
-
John from Stone Mountain, GA
- Really Easy
- 15 - 30 mins
-
Socket set
Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done!
... Read more
Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 people
found this instruction helpful.
-
Xiaobin from Cordova, TN
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people
found this instruction helpful.
-
Paul from Painesville, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Washer will agitate, but won't spin
18 of 24 people
found this instruction helpful.
-
Mandie from Lewisville, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.
I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.
The swit ... Read more ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.
After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.
Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.
The swit ... Read more ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.
After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.
Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
Read less
Was this helpful?
Thank you for voting!
The Agitator in my washing machine wasn't spinning, and was loose.
15 of 15 people
found this instruction helpful.
-
Anton from BRONX, NY
- Really Easy
- 30 - 60 mins
-
Socket set
After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what
... Read more
I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
shut off before finished
17 of 22 people
found this instruction helpful.
-
LARRY from LUCERNE, CA
- Easy
- 15 - 30 mins
-
Screw drivers
i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove
... Read more
the control panel which is easy to do. next time i will read all i can on repairs in this section!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!