110260 Kenmore Washer - Instructions

All Instructions for the 110260
76 - 90 of 2294

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator loose spinning
27 of 28 people found this instruction helpful.
  • Matthew from AUSTIN, TX
  • Easy
  • 30 - 60 mins
  • Socket set
Three of the four agitator cogs had broken. The agitator was able to spin freely both clockwise encounter clockwise which it should not be doing. I replaced the cogs as well as a couple additional parts just to be sure but the cogs were the important one. Very easy.
Was this helpful?
Thank you for voting!
Severe water leak
27 of 29 people found this instruction helpful.
  • Noel from Pollock, ID
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
Was this helpful?
Thank you for voting!
Lid would not register closed washer would not spin
30 of 38 people found this instruction helpful.
  • william from HOLLEY, NY
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Remove top of washer 5min R&R cable 20 min total time 25 min.
Was this helpful?
Thank you for voting!
washer moving 3 ft during the spin cycle sounding like elephants running through the house
29 of 37 people found this instruction helpful.
  • Annie from Haines, OR
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Removed back panel to remove tub from shell. Unscrewed the brackets holding the springs. Used screw driver to pop out pads with hammer onto screw driver. Cleaned out tub and put grease on springs where they attach to bracket. Replaced panel and ran machine to find a leak. Took machine apart again to find the knocking of the tub again st the back panel caused a whole in the plastic tub. Silicon and mechanical tape. Washer works fine for now.
Was this helpful?
Thank you for voting!
Agitatorwouldn't agitate on the washing machine
26 of 28 people found this instruction helpful.
  • Kelly from Newport News, VA
  • Easy
  • 15 - 30 mins
  • Socket set
before ordering the parts, I pulled the cap of the agitator, removed some internal parts of the agitator - had to remove one hex head bolt, and noticed the threads on the 3 little teenie weenie plastic dogs were worn off. I bought the repair kit on line after entering the model number, parts were here in a few days, and the repair took a bout 15 minutes. Works like new again.

The directions provided with the parts were very clear and made the job quick, easy, and painless.
Was this helpful?
Thank you for voting!
COLD WATER WOULD NOT SHUT OFF
26 of 29 people found this instruction helpful.
  • Robert L from Pleasanton, CA
  • Very Easy
  • Less than 15 mins
  • Socket set
Turned off cold water , in plugged the washer, disconnected the HOT and COLD supply to the washer. Removed the screws holding the panel to the upper galf of the back of the washer, in plugged the cold water solenoid valve, removed the two screws holding the cold water valve in place pulled up on the valve to remove it, incereted the new valve in it's place, replaced the hold down screws replaced the electrical plugs, replaced the upprr aluminum covering the top half or the back of the washer, reconnected the water supply lines and turned the water on. check for leaks. Wife said it worked like new.
Was this helpful?
Thank you for voting!
Two leaking hoses in my washing machine
29 of 39 people found this instruction helpful.
  • Marc from Morton Grove, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.
Was this helpful?
Thank you for voting!
water overflowing when filling
34 of 54 people found this instruction helpful.
  • Marni from Buhl, ID
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly d ifferent configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!
Was this helpful?
Thank you for voting!
Agitator directional cogs worn out
26 of 30 people found this instruction helpful.
  • Do n from LAWTON, OK
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.
Was this helpful?
Thank you for voting!
Over shaking and knocking on the side
25 of 28 people found this instruction helpful.
  • Alain.m from HARLINGEN, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was r eally happy so me. It can be done by anybody but first go on the internet to get a idea.
Was this helpful?
Thank you for voting!
Lid Switch
25 of 28 people found this instruction helpful.
  • Diane from South Windsor, CT
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
Removed all screws to electronic knob panel, unplugged lid switch from panel. Removed washer surround and unclipped wires. Since I had the surround removed, I was able to view the washer drum. Decided to remove all tub clips and clean tub and removed all built up soap and lint. Did the reverse and re-clipped, rescrewed and put surroun d back together. Hardest problem was putting the washer surround back on the tub. I'm not an extremely strong woman - but did it just the same. Neglected to advise I'm unemployed and recently had a quadrouple bypass. Needed to save money, Sears quoted me $300.00 to fix the machine. No way would I pay that amount of money so I did it myself. Thank you very much!
Was this helpful?
Thank you for voting!
Water constantly dripped into washer when it was off.
24 of 25 people found this instruction helpful.
  • MARK from MARION, MA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
Was this helpful?
Thank you for voting!
Waher would not spin and made noise
25 of 29 people found this instruction helpful.
  • Andrew from SYLVANIA, OH
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Was this helpful?
Thank you for voting!
Lid closes, switch wouldn't turn on machine.
31 of 47 people found this instruction helpful.
  • Kenneth from Wilmington, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Was this helpful?
Thank you for voting!
Agitator was locked up
24 of 28 people found this instruction helpful.
  • Roger from Palmyra, IN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two ho ses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger
Was this helpful?
Thank you for voting!
All Instructions for the 110260
76 - 90 of 2294