110225 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator was barely agitating. Making a clicking noise.
17 of 18 people
found this instruction helpful.
-
Charmaine from Slidell, LA
- Easy
- 15 - 30 mins
-
Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
Smelled a burning odor occasionally
17 of 23 people
found this instruction helpful.
-
Paul from E NORTHPORT, NY
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set, Wrench (Adjustable)
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash
... Read more
er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Read less
Was this helpful?
Thank you for voting!
My tub would hit the sides of the washer during spin cycle.
13 of 15 people
found this instruction helpful.
-
ELIZABETH from HARLINGEN, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Followed youtube video. The repair was easy and fast.
Was this helpful?
Thank you for voting!
Agitator moves freely in both directions
14 of 18 people
found this instruction helpful.
-
James from NAPERVILLE, AL
- Really Easy
- Less than 15 mins
-
Wrench set
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and
... Read more
pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Read less
Was this helpful?
Thank you for voting!
Whirlpool builds junk lid switches don't lasting when you have suffered water! About every 3 months it goes out! Repairman won't come to fix so I do it myself!
13 of 17 people
found this instruction helpful.
-
Charlie from OAKWOOD, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplug washer
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Washer was rumbling at the spin cycle
10 of 10 people
found this instruction helpful.
-
Teamos from Frisco, TX
- Very Easy
- Less than 15 mins
-
Pliers
Unplugged, removed cold and hot lines, moved out to garage, unscrewed 3 screws on the back, lifted up the top, removed and replaced 1 suspension rod at a time with washer leaning against wall sideways, easy peasy didn’t take no time at all, moved it back in 3 screws back in place hot and cold screwed back in and walla! It worked and has
... Read more
been working flawlesssly..
Read less
Was this helpful?
Thank you for voting!
squeal and chirping while in risne / spin mode
10 of 10 people
found this instruction helpful.
-
Thomas from GRAIN VALLEY, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
FAULTY LATCH-WASHER WOULD NOT GO INTO SPIN MODE
11 of 14 people
found this instruction helpful.
-
EVAN from STOCKTON SPGS, ME
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
THE NEW LATCH COMES WITH A NEW BEZEL ATTACHED, WHICH MOUNTS TO THE TOP OF THE WASHER, JUST UNDERNEATH THE LID. BECAUSE THE ORIGINAL BEZEL WAS IN PERFECT CONDITION AND DIFFICULT TO REMOVE, I DECIDED TO REMOVE THE BEZEL ON THE NEW LATCH, AND USE THE ORIGINAL ONE. THIS WOULD HAVE TO BE DONE REGARDLESS IN ORDER TO INSTALL THE NEW LATCH. REMO
... Read more
VING THE BEZEL WAS DIFFICULT DUE TO ALL THE LOCKING TABS THAT KEEP IT IN PLACE. I HAD TO RESTRAIN THE SLIDING SWITCH PARTS WHILE I REMOVED TO BEZEL TO AVOID THE ASSEMBLY FROM COMING APART. ONCE I SNAPPED THE NEW LATCH TO THE EXISTING BEZEL, THE ASSEMBLY WORKED FINE. TAKE TIME TO STUDY HOW THE LATCH ASSEMBLY IS ATTACHED TO THE BEZEL SO THAT YOU DON'T BREAK SOMETHING. USE A VERY SMALL SCREWDRIVER TO PRY BACK THE PLASTIC TABS IN ORDER TO RELEASE THE BEZEL FROM THE LATCH ASSEMBLY.
Read less
Was this helpful?
Thank you for voting!
washer shaking and banging loudly
10 of 12 people
found this instruction helpful.
-
PRECIOUS from LAKE CITY, FL
- Easy
- 30 - 60 mins
-
Screw drivers
I was able to look up the issue on Youtube and watched a few videos and was able to complete the repair with help of my daughter. It was little hard to do but you do need gloves with a good grip when taking the rods out of the washer, but putting the new ones in was very easy.
Once I replaced the suspension rods, there was a li ... Read more ttle shaking but not like before. Very quiet now, no crazy loud banging
Once I replaced the suspension rods, there was a li ... Read more ttle shaking but not like before. Very quiet now, no crazy loud banging
Read less
Was this helpful?
Thank you for voting!
When the washer would go into spin cycle it sounded like the drum was banging all four sides of the washer.
9 of 9 people
found this instruction helpful.
-
LADD from ARCADIA, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Unplugged from power, unhooked water lines.Then removed back cover and control panel and top set to the side. Rear rods very easy to do by yourself after those where done have help and tip it backwards and change out the front 2 then reassembled and hooked back up and tested. Everything worked like brand new !!!
Was this helpful?
Thank you for voting!
Banging during spin cycle
9 of 10 people
found this instruction helpful.
-
Rachel from PINELLAS PARK, FL
- Very Easy
- 30 - 60 mins
-
Socket set
The installation was very easy and took me 45 minutes to complete by myself. I put the washer on two cinder blocks and then removed the lid. I started with the suspension rods that were closest to me and they were really easy to exchange. When I got to the rods in the back they were a little more difficult because there was more tension w
... Read more
ith the new rods installed. I used the old rods to hook and pull the new rods into place and it was overall very easy.
Read less
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people
found this instruction helpful.
-
Elzoria from FROSTPROOF, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people
found this instruction helpful.
-
Larry from HICKORY, NC
- Very Easy
- Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Read less
Was this helpful?
Thank you for voting!
Shaking and banging around when washing
9 of 10 people
found this instruction helpful.
-
Jessica from MT STERLING, KY
- Easy
- 15 - 30 mins
-
Screw drivers
Youtube has videos. It's very simple just replace one at a time.
Was this helpful?
Thank you for voting!